油槽用英语怎么说，油槽的英文翻译

词语导航

基本信息

词语：油槽

繁体：油槽

拼音：yóu cáo

英语翻译

【化】 oil scupper

相关词条

1.oilsump  2.petroleumtank  3.oilscupper  4.tank  5.oil-bath  6.oilgroove  7.oilspace  8.oiltank  9.oilreceptacle  10.easegroove  11.oilwell  12.oilslot  

分词翻译

油的英语翻译：

paint; fat; grease; oil
【化】 oil
【医】 elaeo-; eleo-; oil; Ol; olea; oleo-; oleum

槽的英语翻译：

chamfer; gutter
【计】 slot
【化】 channel
【医】 alvei; alveus; crib; gutter; slot; socket; tank; trough

翻译例句

1. 必要时，从煞车油槽卸下一些煞车油。

If necessary, remove some brake fluid from the reservoir.

2. 介绍一种加工不贯通油槽的可调夹具。

This paper introduces a kind of adjustable fixture in which processes incoherence oil groove.

3. 我的油槽必须加满无铅汽油。

My gas tank needs to be filled with unleaded.

4. 轴承的油槽要滚铣和倒角。

The oil grooves of the bearing should be milled gear.

5. 放置支撑架于储油槽底下。

Place the support frame at the bottom of the oil storage tank.

6. 可与壳体分离的油槽使其更换简单、方便。

The replacing is easy and convenient as the oil groove can be separated with the shell.

7. 汽油从油槽漏隙滴下。Www.WeNTIYi.com

Gasoline dribbled from the leak in the tank.

8. 滑动并敲击贮油槽扣件夹，直至凸耳锁紧外壳。

Slide and tap in reservoir retainer clips until TAB locks to housing.

9. 油槽卡车一扫过。

Oil tankers are gliding past.

10. 第一周，电阻将被放在一个油槽中直到温度稳定。

For the first week, the resistor will sit in one of the oil baths until its temperature stabilizes.

11. 关闭数控弹簧机电源，等待五分钟让循环机油流回储油槽。

Turn off the power, a CNC spring machine, wait five minutes for the oil to flow back into the oil storage tank circulation.

12. 外球面球轴承外圈一般带油槽，也生产外圈无油槽的产品。

Usually, the outer ring of the tl bearings has grease groove, bearings having no grease groove are to be provided, too.

13. 软钢SC-11焊条是用于管子、油槽、锅炉等用直流焊接。

Mild steel welding is used in SC - 11, bulges, boiler tube with dc welding etc.

14. 现有打火机的油槽内存储可燃气体，其外壁作为打火机的壳体。

Combustible gas is stored in an oil groove of the present lighter; the outer wall of the oil groove is used as the shell of the lighter.

15. 讨论了油槽宽度、深度及油槽数目对承载能力和传递扭矩的影响。

The influence on load capability and torque transmission made by width and depth of oil wedge and its number are also discussed in this paper.

16. 简介了电火花成形机工作油槽柔性升降系统的工作原理及设计方法。

The work principle and design method for flexible work tank elevator of EDM machine tool are briefly introduced.

17. 本文对在淬火油槽内用超声波振动提高油冷却能力的试验进行了研究。

This paper deals with the experimental study of improvement on the oil cooling ability by producing ultrasonic wave vibration in the quenching oil trough.

18. 一些人说虽然这些燃油不能灌满油槽，但是这些油够他们好好度个周末了。

Some say while this won"t fuel the tank, it will get them through the holiday weekend.

19. 在装有循环装置的空气炉或油槽中进行热处理：一定温度下保温一段时间。

Equipped with cycle device in the air or the oil heat treatment furnace in certain temperatures: thermal insulation for a period of time.

20. 其中最有效的就是适当加大“C”节流器的流量和改变放油针油槽的结构设计。

The most effective measures are enlarging the discharge of the "C" throttle unit and modifying the structure of the metering pin oil groove.

21. 涂料输送泵变频调速，流量控制稳定，涂料箱（油槽）恒温控制，漆膜分布均匀。

Paint conveying pump frequency control, flow control and stability, paint tank (tank) temperature control, filmdistribution.

22. 本实用新型可以实现在线清洗正在使用的卷绕油槽，同时便于进行更换油剂操作。

The utility model can realize the cleaning of a winding oil groove being used on line and is also convenient for replacing oil solution.

23. 油槽中的油着火只能用干粉灭火器灭火，如果在这种情况下用水灭火可能导致爆炸。

To fight fire on oil tanks use only powder-type fire extinguishers. If water were used in this case, there would be the risk of explosion.

24. 该装置主要由热载体烤漆炉、辐射加热管，热载体炉、膨胀器、油气分离器和储油槽等组成。

The new device consists of paint-drying box, heat carrier boiler, heating pipe, expansion tank, gas separator and oil tank, etc.

25. 打火机被碰撞或跌落到地面上时，油槽直接与其接触，容易破裂和漏气，会对人造成潜在危险。

When the lighter is hit or falls off on the ground, the oil groove is contacted with the ground directly and is easy to break or leak, which is dangerous potentially to people.

26. 本文介绍一种加热装置的制作，该装置可代替热敏电阻温度系数测量实验中的加热油槽或水槽。

This paper presents the making of a heating device, which can be used to replace the heating of oil sink or water sink in the experiment of measuring heat-sensitive resistance temperature coefficient.

27. 本文介绍一种加热装置的制作，该装置可代替热敏电阻温度系数测量实验中的加热油槽或水槽。

This paper presents the making of a heating device, which can be used to replace the heating of oil sink or water sink in the experiment of measuring heat-sensitive resistance temperature coefficient.