安装接头用英语怎么说，安装接头的英文翻译

词语导航

基本信息

词语：安装接头

繁体：安裝接頭

拼音：ān zhuāng jiē tóu

英语翻译

【化】 field joint

相关词条

1.erectionjoint  

分词翻译

安装的英语翻译：

fit; fix; install
【计】 erecting
【化】 setting
【经】 installation

接头的英语翻译：

connect; get in touch with; joint; piece
【计】 splice
【化】 adapter

翻译例句

1. 这些图纸应说明备用连接的所有的必要尺寸，安装接头，位置和尺寸。

These drawings shall show all necessary dimensions, all field joints, location and sizes of auxiliary connections.

2. 自1981年起生产的轿车都有安装安全保护装置的接头。

All cars built since 1981 have points for the attachment of safety restraints.

3. 在拧管道接头螺丝时，应遵循对角互拧的原则，不要逐个顺序进行操作，不要一次性将螺丝拧死，这样才能将橡胶垫片正确地安装上去。

When the pipe joint screw, should follow the principle of diagonal twist, not one by one in order to operate, do not screw the screw die, so that the correct installation of rubber gasket.

4. 承包商应于接头安装后一周重新拧紧螺母，并就在轨道最终衬砌和整平前再一次拧紧。

The contractor shall retighten the nuts one week after joint installation and a second time just before final lining and leveling of the track.

5. 采用安全可靠的航天接头，充分保护电路的稳定性。整并的电路系统，不但安装简易而且维护方便。

Adopts safety and reliable spaceflight joint, sufficient protects the stability of the circuit. The whole circuit system, not only easy to install but also maintenance is convenient.

6. 需要时，绝缘接头应在轨道最终衬砌和整平前安装。

Insulated joints if required shall be installed just before final leveling and lining of the track.

7. 广泛应用的材料、金属支架与接头都由建筑师精心挑选，并根据空间和结构的要求，进行安装。

Widely utilised materials, metal brackets and joints, are carefully selected and positioned with respect to both the spatial and structural requirements.

8. 采用电加热法加热时，需注意热电偶及加热圈的安装要尽可能靠近坡口，但不得妨碍焊工接近接头。

When an electric heating method is used for heating, thermal couple and heating coil should be installed closest to the bevel while should not hinder the access of welder to the joint.

9. 我们生产的软管和接头很方便安装，对于任何没有操作经验的人来说都能很简单地操作。

Because no handiness is required for mounting hoses and connection parts we produce, it is quite easy for anyone without experience.wwW.WEntiyI.coM

10. 将存储座位模组滑离两个安装支架滑式舌片，直至足以够着并拔下线束接头。

Slide the memory seat module off of the two mounting bracket slide tabs far enough to access and unplug the wire harness connectors.

11. 各种各样的伸缩接头被安装在蒸气管道上了。

Expansion joints of various kinds are fitted on steam pipes.

12. 系列ETX可以安装在丁字接头或任何其他适合的加热系统接头上，可以垂直安装，也可以水平安装。

Series ETX may be installed in a tee or any other suitable tapping in the heating system and can be installed in a vertical or horizontal position.

13. 接头安装时管螺纹上应缠绕适当的生料带，以确保其密封的可靠性。

Joints should be installed on the pipe thread wrapped with the appropriate raw material to ensure the reliability of sealing.

14. 不能小于安全阀的管道口径，也不能在排泄管上安装任何缩径管接头。

Must not be smaller than the pipe size of the relief valve or have any reducing coupling installed in the discharge line.

15. 紧固件将装饰板的上部连接到安装在飞机结构上的接头上。

Fasteners attach the upper part of the decorative panels to the attachment fittings mounted on the aircraft structure.

16. 反接对线错误发生在线对是正确安装在一连接头时，但是在另一个连接头却反接。

The reversed-pair fault occurs when a wire pair is correctly installed on one connector, but reversed on the other connector.

17. 绝缘接头避免安装在立管上。

Avoid install the insulation joint on the vertical pipe.

18. 建议在热水和冷水管线上安装管接头，以方便热水器的维修或更换。

The installation of unions in both the hot and cold water supply lines is recommended for ease of removing the water heater for service or replacement.

19. 下放伸缩隔水管，将伸缩隔水管顶部接头安装到转喷器壳体上。

Lower the slip joint and fix its top connector into the diverter.

20. 检查钢轨接头，不得有错位及错位；安装无松动、脱落。

2 check rail joints, shall not have dislocation and dislocation; installation without loosening, shedding.

21. 光缆接头筒外形是椭圆型直立式结构设计，筒和底座采用抱箍锁紧固定密封，安装十分方便。

Dome is a vertical type. hoop is used to fix and seal fosc cover and base, and its installation is quite simple.

22. 其安装步骤与应用于硬盘的步骤相似：确定跳线，将电缆接头与驱动器和主板分别连接，然后将光驱置于固定托盘中。

The steps resemble those applicable to hard drives: verify the jumpers, attach the cable connectors to the drive and to the board, and then fit the CDROM into its tray.

23. 在玻璃钢管道系统铺设中选用合理的安装措施，不设置膨胀接头，也能保证管线长期安全使用。

The long-term safe usage can be kept without expanding joint in the FRP pipe system if rational assemble measures are selected.

24. 除非另行规定，否则，加工商应安装所有管线内装置、控制面板及工艺接头并包含一级开关阀。

Unless otherwise indicated, the fabricator shall install all in-line devices, control panels, and process taps up to and including the primary shutoff valve.

25. 使用时注意接头质量、托辊转动应灵活、表面安上护套，采用在各滚动轮上安装衬垫等措施有效地提高钢丝绳的使用寿命。

Some measures as fittings quality, cradle roll"s flexibility, and installing cleading in face, installing mat in every rolling wheel and etc. can increase wire rope"s service life.

26. 斯特劳勃管接头的安装快速，简单，可靠。

The installation of a STRAUB pipe joints is fast , simple and reliable .

27. GT系列气动执行器可与阀门直接连接，也可通过支架和接头与阀门安装连接。

GT series pneumatic actuators can be directly connected with the valve, brackets and fittings can also be connected with the valve installation.

28. 那么这条缝可以在车间焊接。在处理和安装熔接接头的成品管段时应特别小心。

But care shall be taken on fusion welded joints of fabricated spools during handling and installation.

29. 那么这条缝可以在车间焊接。在处理和安装熔接接头的成品管段时应特别小心。

But care shall be taken on fusion welded joints of fabricated spools during handling and installation.