
词语导航
基本信息
词语:出口节点
繁体:出口節點
拼音:chū kǒu jié diǎn
英语翻译
【计】 exit node
分词翻译
出口的英语翻译:
exit; escape; export; issue; outcome; outlet; speak out; vent
【医】 exitus; outlet; portal of exit
【经】 export; exports
节点的英语翻译:
【计】 node; node point
【化】 nodal; nodal point; node
【医】 Gaussian points; nodal points
【经】 node
翻译例句
1. 接下来在点(3)处,在节点处理完成后调用了用户出口。
Next, at point (3), the user exit is invoked after the node processing is completed.
2. 随后在点 (2) 处,在消息传播到该节点进行处理时调用了用户出口。
Subsequently, at point (2), the user exit is invoked when the message is propagated to the node for processing.
3. 在点(1)处,紧跟在节点传播消息之前调用了用户出口。
At point (1), the user exit is invoked just before the node propagates the message.
4. 注意:在点(1)处,在内置输入节点上调用用户出口的方式与在用户定义的输入节点上稍有不同。
Note: At point (1), the way user exits are invoked on the built-in input nodes is slightly different from the user-defined input nodes.
5. 用户出口并不仅限于内置节点,它们适用于所有用户定义的插件节点。WwW.wENtiyi.COm
User exits are not limited to built-in nodes, they are applicable to all user defined plug-in nodes.
6. 用户出口API在用户定义的c节点api中提供。
The user exit APIs are provided inside the C user-defined node APIs.
7. 除非使用一个通道自动定义出口,否则WebSphereMQ集群中的所有远程节点的授权都将基于集群接收器通道定义中的mcauser值。
Unless a channel auto-definition exit is used, authorization of all the remote nodes in the WebSphere MQ cluster is based on the MCAUSER value in the cluster receiver channel definition.
8. 给水泵汽轮机模型采用TUPWR算法,给水泵系统采用SFPUMP算法,最小流量阀采用SOVLV算法,泵出口流量的关系采用压力节点进行计算。
TUPWR algorithm was adopted for the pump turbine model, SFPUMP for feed pump system, SOVLV for minimal flow valve, and pressure node for calculating the discharge rate of the pump.
9. 利用SIMPACK建立某出口2b0机车动力学模型,分析了转臂轴箱定位节点的纵向位置对机车动力学性能的影响。
The dynamic model of a 2b0 locomotive for export is built with software SIMPACK to analyze the influence of longitudinal position of the locating node for tumbler axle-box on locomotive dynamics.
10. 提高进口烟气温度、降低蒸汽压力或减小节点温差,均可显著降低设计出口烟气温度,从而增大蒸发量,提高热效率;
Higher gas inlet temperature, lower steam pressure or pinch point temperature difference lead to lower exhaust gas temperature, larger evaporation and higher efficiency;
11. 提高进口烟气温度、降低蒸汽压力或减小节点温差,均可显著降低设计出口烟气温度,从而增大蒸发量,提高热效率;
Higher gas inlet temperature, lower steam pressure or pinch point temperature difference lead to lower exhaust gas temperature, larger evaporation and higher efficiency;
版权声明:问题易所有作品(图文、音视频)均来源网络,版权归原创作者所有,与本站立场无关,如不慎侵犯了你的权益,请联系我们告知,我们将做删除处理!
