传热速率用英语怎么说,传热速率的英文翻译


词语导航

基本信息

词语:传热速率

繁体:傳熱速率

拼音:chuán rè sù shuài

英语翻译

【化】 heat transfer rate

分词翻译

传热的英语翻译:

【化】 heat transfer; heat transference; heat transmission
thermal transmission

速率的英语翻译:

rate; speed; tempo; velocity
【化】 rate; speed
【医】 speed; velocity

翻译例句

1. 结果表明(火用)损失和化学反应及传热速率成正相关。

The results show that the exergy loss is directly proportional to the rates of chemical reaction and heat transfer.

2. 因此,在沥青基炭纤维形成过程中,控制温度和传热速率是极为关键的。wWW.WentIyi.cOM

Therefore, the control of both temperature and heat-transfer rate is extremely critical during the formation of pitch-based carbon fibers.

3. 模型中采用传质、传热速率方程表征实际塔板上的传递过程,避免了级效率的计算。

Mass and energy transfer rate equations are used in describing the transfer processes on real trays and thus the computations of stage efficiencies are entirely avoided.

4. 在连铸过程中结晶器的传热速率对铸坯的表面质量和防止漏钢都具有十分重要的影响。

The rate of heat transfer in mould affects significantly on the surface quality of slab and protection of steel breaking in continuous casting.

5. 对脉动流化床内换热面与床层的传热特性进行了试验研究,试验中观察到的脉动床最大传热速率比普通流化床的传热速率提高15%左右,对于较大直径的颗粒,脉动流化床的传热效果更突出;

The results show that the heat transfer rate in a pulsed fluidized bed is 15%greater than that in a normal fluidized bed. The bigger the particles, the higher the heat transfer efficiency.

6. 第一个问题涉及热力学,第二个问题涉及各种速率过程——化学动力学,传热等。

The first question concerns thermodynamics, the second the various rate processes- -chemical kinetics, heat transfer, etc.

7. 这些是在流体性质,流动速率,传热面上的缩放和沉淀中是可能变动的结果。

These are the results of possible variations in fluid properties, flow rates, scaling or deposits on the heat transfer surfaces.

8. 研究结果表明强化气相与水合物颗粒之间的接触传热对提高水合物的生成速率具有十分重要意义。

The result shows that it can effectively accelerate the rate of hydrate formation by enhancing the heat transfer between the gas phase and hydrate particle.

9. 在铁浴熔融还原时,为保证较高的传热和反应速率,熔池中泡沫渣应保持一个适当的高度。

For the smelting reduction in iron bath, the foam should be kept in a suitable height in order to obtain a high rate heat transfer and reaction.

10. 最大聚合速率与聚合釜传热能力的均衡是达到缩短聚合时间、提高生产能力的重要环节。

The balance between the maximum reaction rate and the heat transfer capacity of the reactor was the key factor for shortening of polymerization time and improving the production capacity.

11. 探索了该装置内的两相流流型及传热系数、循环速率与热通量的关系。

A two-phase flow patterns, the relationship between the heat transfer coefficients and heat flux and the relationship between the recirculation flow rate and heat flux are investigated.

12. 对直接接触式二元冰蓄冷系统制冰罐内的传热特性进行了研究,对影响制冰罐内容积换热系数的各种影响因素进行了分析,最后对容积换热系数对制冰速率的影响进行了讨论。

Heat transfer characteristic of ice storage tank of direct contact ice slurry system was studied, the influence factor of volumetric heat transfer coefficient in the ice slurry tank was analyzed.

13. 以实验验证计算结果,并详细讨论了喷涂沉积速率、界面传热系数以及间歇喷涂对涂层温度场的影响。

Experiments proved that the calculation results are believable. The influence of deposition rate, coefficient of heat transfer and spraying process on coating temperature field was discussed.

14. 该模型学习速率快,训练步骤少,逼近程度高,最大偏差不大于5%,为三相循环流化床蒸发器的传热计算提供了可靠的方法和理论基础;

Rapid learning speed, few training steps and high fidelity are advantages of the model. The maximal deviation is no more than 5%.

15. 但环氧树脂传统的热固化方法由于存在着传热速度慢、温度梯度大、固化不均匀和固化速率低等问题,严重影响了环氧树脂基复合材料的固化质量。

The effect of microwave curing on the curing velocity, mechanical and thermal properties of epoxy and epoxy matrix composites were discussed emphatically and in detail.

16. 本文研究传热不可逆,过程进行速率有限对磁性斯特林制冷机最优性能的影响。

In this paper, the effect of the irreversibility of heat conduction and finite rate processes on the optimal performance of a magnetic Stirling refrigerator is researched.

17. 本文研究传热不可逆,过程进行速率有限对磁性斯特林制冷机最优性能的影响。

In this paper, the effect of the irreversibility of heat conduction and finite rate processes on the optimal performance of a magnetic Stirling refrigerator is researched.

版权声明:问题易所有作品(图文、音视频)均来源网络,版权归原创作者所有,与本站立场无关,如不慎侵犯了你的权益,请联系我们告知,我们将做删除处理!