
词语导航
基本信息
词语:安装垫片
繁体:安裝墊片
拼音:ān zhuāng diàn piàn
英语翻译
【化】 mounting pad
分词翻译
安装的英语翻译:
fit; fix; install
【计】 erecting
【化】 setting
【经】 installation
垫片的英语翻译:
【化】 gasket; shim; spacer
翻译例句
1. 将再循环风扇的接耳放置在正确位置,安装垫片、螺钉、螺帽。
Put the recirculation fan lugs in position and install the washers, the bolts, the washers and the nuts.
2. 在拧管道接头螺丝时,应遵循对角互拧的原则,不要逐个顺序进行操作,不要一次性将螺丝拧死,这样才能将橡胶垫片正确地安装上去。
When the pipe joint screw, should follow the principle of diagonal twist, not one by one in order to operate, do not screw the screw die, so that the correct installation of rubber gasket.
3. 在人造纤维行业,各滤网都要安装与其轮廓相吻合的垫片和密封圈。
Along with screen packs, the synthetic fiber industry utilizes gaskets and seals with each pack configuration.
4. 必须采取适当的矫正措施来消除这些障碍物,例如对管道镗圆锥形孔或安装间隔垫片。
Suitable corrective measures must be taken to remove these obstructions, such as taper boring the pipe or installing a spacer.
5. 由于膨胀机碳环密封后面的密封垫片在安装时未被充分压紧,使膨胀机机体及相应管道进油。
At installation, insufficient compression of the sealing pad behind the carbon ring seal of the expander results in oil entrance to expander body and to the corresponding pipeline.
6. 安装带法兰的管路时,必须在两个对接法兰的密封间放置垫片。
When installing the pipeline with flange, the gasket must be placed between the two butt flanges.
7. 符合IP65当正确安装使用的密封垫片供应。
IP65 when properly installed using the sealing gasket supplied.
8. 文章介绍了船舶主机齿轮箱在安装过程中,如何保证轴系校中要求和齿轮箱环氧树脂垫浇注工艺以及垫片及螺栓强度计算,可供同行借鉴。
This article introduces the requirements of aligning to the installation of gear case and construction process, calculating for sheets of epoxy resin chock for gear case on board.
9. 安装在前部和后部的垫片厚度可能不同。
There is a possibility that the thickness of filler plates for front and rear mount is different.
10. 机床的安装区域内,如果地基平面的高度差超过本产品的调节范围时,可以在机床与负荷盘间增加垫片。
The installation of machine tools within the region, if the ground plane height difference over the adjustment range of this product, you can set the machine and load has increased by pads.Www.wENTIyi.com
11. 安装时请注意阀体上标注介质流向,两法兰连接时必需加密封垫片,然后均匀锁紧螺栓。
When installation, note flow direction of media of valve body. When connecting two flanges, add sealing mat. Then lock the bolt evenly.
12. 本阀可水平安装或垂直安装,安装时两法兰联接中间必须加密封垫片,然后均匀锁紧螺栓。
The valve can be installed in horizontal or vertical. Add seal cushion between two flanges connection and screw down bolt.
13. 这种止回阀应用于玻璃管线系统中,安装在两个装有垫片的连接法兰中间。
This check valve is used in systems that utilize glass pipe and installs between connecting flanges where a gasket would normally be located.
14. 本阀可水平安装或垂直安装,安装时两法兰连接中间必须加密封垫片,然后锁紧螺栓。
It can be installed in horizontal or vertical. Sealing gasket must be put on the connected, then equably tight the bolt.
15. 平垫片和弹簧垫片,它们安装在防退膨胀管和螺栓六角帽之间的螺杆上;
The flat gasket and the spring gaskets are arranged on the bolt between the ante-receding expansion pipe and the hexagonal cap of the bolt.
16. 安装时请注意阀体上标注介质流向,两法兰连接时必需加密封垫片,然后均匀锁紧螺栓。
Pay attention to the direction of medium in valve body. Add seal cushion between two flanges connection and screw down bolt.
17. 这种阀门是为安装于尾端为沟槽的装置而设计的,取代了这种情况下通常的通过垫片安装。
The valve is designed to fit into grooved end clamp type fittings and replaces the gasket normally used with these fittings.
18. 这种阀门是为安装于尾端为沟槽的装置而设计的,取代了这种情况下通常的通过垫片安装。
The valve is designed to fit into grooved end clamp type fittings and replaces the gasket normally used with these fittings.
版权声明:问题易所有作品(图文、音视频)均来源网络,版权归原创作者所有,与本站立场无关,如不慎侵犯了你的权益,请联系我们告知,我们将做删除处理!
