
词语导航
基本信息
词语:预热温度
繁体:預熱溫度
拼音:yù rè wēn dù
英语翻译
【化】 preheat temperature
分词翻译
预热的英语翻译:
warm-up
【机】 preheat; preheating
温度的英语翻译:
temperature
【化】 temperature
【医】 T; temperature
翻译例句
1. 提高基体预热温度可有效避免熔覆层开裂。
The analysis results also show that enhancing preheating temperature is an effective way to avoid cladding layer cracking.
2. 预热温度在焊接开始到结束期间应保持均衡。wwW.WeNTiyi.coM
Preheating temperature shall be kept uniform from the start to the end of welding.
3. 对于不同尺寸的颗粒,都存在一个临界预热温度。
There exists a critical preheating temperature for different size of granules.
4. 本文研究了焊缝中扩散氢含量与预热温度的关系。
In this paper, the influence of pre heating temperature on the content of diffusive hydrogen in weld joint was studied.
5. 针对X80管线钢进行了焊接性分析,确定其预热温度。
The weldability of X80 pipeline steel was analyzed and its preheating temperature was determined.
6. 研究了不同空气预热温度对低热值煤气燃烧过程的影响。
The effects of air preheating temperature on the burning characteristics of low calorific value gas was studied.
7. 钢芯线预热温度和铜液温度的升高使包覆比下降,重熔时间缩短。
The increase of the preheating and liquid copper temperature of copper clad steel wires makes the cladding ratio down and the remelting time short.
8. 蒸发过程中,电解液预热温度作为主要的工艺操作条件之一,尤为重要。
The process of evaporation, electrolyte preheating temperature as one of the main process operating conditions, particularly important.
9. 初始预热温度是指任何焊接操作开始之前,焊接区域内工件的瞬时温度。
Original preheating temperature: the temperature of the workpiece in the weld zone immediately prior to any welding operation.
10. 研究表明:模具预热温度影响最大,压射速度次之,浇注温度影响最小。
The results show that mold temperature is the most significant influence factor, injection speed takes the second place, and pouring temperature is the least significant influence factor.
11. 研究了渗流驱动压力、 铝熔体浇铸温度及模具预热温度对渗流过程的影响;
The effects of infiltration pressure, casting temperature and preform particles temperature on the preparation process were analyzed.
12. 同时总结了一套计算焊接预热温度确定方法和焊接接头匹配的选取原则与方法。
In addition, a calculating method on welding preheating temperature and a selective principle and method on welding component matching are concluded.
13. 但预热温度不宜过高,以免引起基体表面氧化而影响涂层与基体表面的结合强度。
However, the preheating temperature should not be too high, so as to avoid matrix effects of surface oxidation and surface coating and the substrate bonding strength.
14. 考察了氯化反应器、预热温度、氯气流速、反应温度及反应时间对氯气转化率的影响。
The effects of chloridization reactor, preheat temperature, chlorine flow rate, reaction temperature and reaction time on the conversion of chlorine gas were examined.
15. 预热温度及层间温度控制在25 ~50为宜,接头拉伸和冲击性能与母材相匹配。
The preheating and interpass temperatures are 25 ~ 50c. Tensile and impact properties of the joints are almost the same as that of the matrix.
16. 研究了粉体预热温度、频率、环境温度等工艺参数及条件对PZT陶瓷电性能的影响。
The effects on electric properties of PZT ceramic were investigated, including preheating temperature, frequency, environment temperature and polarization.
17. 在进行碳钢及低合金钢的焊接时应进行预热。预热温度在焊接开始到结束期间应保持均衡。
Preheating shall be carried out for carbon and low alloy steel welding where required. Preheating temperature shall be kept uniform from the start to the end of welding.
18. 系统研究了激光功率、扫描速度、预热温度、铺粉厚度等工艺参数对成型试样质量的影响。
The effects of different process parameters such as laser power, scanning speed, preheat temperature, powder-bed depth on the sintered quality were studied systematically.
19. 激光掺杂存在一个阈值能量密度。掺杂浓度和深度的分布与预热温度和杂质镀层厚度有关。
It is found that there is a threshold energy density in laser doping, and distributions of dopant density and depth have relation to preheat temperature and plating layer thickness of the impurities.
20. 此换热器空气阻力大,空气预热温度不高,风机压头高,环境噪声大,风机振动大、易损坏。
The recuperators have high air resistance , low air preheating temperature and high fan pressure head , and fan has much noise to environment and are apt to break down with vibration .
21. 在采用连续挤压包覆技术生产铜包钢接触线时,钢丝的预热温度对产品的质量有重要的影响。
The temperature of steel wire affects the quality of the copper clad steel contact wire when it is produced with new craft of continuous extrusion.
22. 随着预热温度的提高,电阻峰值也相应增大,但是样品下表面的热导出率下降,冷却速度下降;
With preheating temperature enhancing, the peak value also increase, but cooling velocity decreases, resulting from the decrease of heat conductivity of sample lower surface.
23. 通过焊接热模拟试验和冲击韧性试验,研究了不同预热温度对X80级管线钢组织性能的影响。
Welding thermal simulation technique is adopted to study the influences of twice thermal cycle on the structure and properties of X80 pipeline steel.
24. 通过焊接热模拟试验和冲击韧性试验,研究了不同预热温度对X80级管线钢组织性能的影响。
The effect of hot bending and heat treatment thermal cycles on the mechanical properties of X80 grade steel pipe was evaluated.
25. 采用本发明预热温度高,热损失少,节省燃气,能耗少,能够将空气温度预热到炉温的80%以上。
The invention has the advantages of high preheating temperature, gas-saving, less heat loss and energy consumption, and the air temperature can be preheated over 80 percent of the furnace temperature.
26. 另外建压时间、坯料加热温度、模具预热温度以及脱模剂等参数对半固态压铸件性能也有明显的影响。
Furthermore, the property of die castings have also been affected obviously by other process parameters, such as time of intensified pressure, mould temperature, billet temperature and lubricant etc.
27. 然后,本文通过正交试验的方法研究了压射速度、浇注温度和模具预热温度对铸件缩松缩孔缺陷的影响。
By use of orthogonal test design, how the injection speed, pouring temperature and mold temperature effects the casting shrinkage porosity forming is studied.
28. 通过改变送粉激光熔覆过程中的扫描速度、送粉速率、基体预热温度等工艺参数,获得了单道激光熔覆层。
Single pass laser surface of the specimens using powder feeding method were obtained by varying the powder feeding rate and the preheating temperature of the substrate.
29. 在含氧体积分数为36%以内提高空气预热温度和含氧浓度,可明显地提高热效率,降低钢坯的氧化烧损。
Under oxygen concentration 36% the higher air temperature and the higher oxygen concentration are, the higher heat efficiency is and the less oxidation loss is obviously.
30. 对预热温度、焊料槽温度和焊剂体积进行优化后,还可将传送带速度降低,以适应使用无铅焊料时的熔湿速度。
Having optimized preheat temperatures, solder pot temperatures, and flux volume, the conveyor speed may have to be reduced to accommodate the solder wetting when using lead-free solder.
版权声明:问题易所有作品(图文、音视频)均来源网络,版权归原创作者所有,与本站立场无关,如不慎侵犯了你的权益,请联系我们告知,我们将做删除处理!
