轴肩用英语怎么说,轴肩的英文翻译


词语导航

基本信息

词语:轴肩

繁体:軸肩

拼音:zhóu jiān

英语翻译

【化】 shaft shoulder

相关词条

1.shoulderofspindle  2.shoulder  3.shaftcollar  

分词翻译

轴的英语翻译:

axes; axis; shaft; spindle
【医】 ax-; ax.; axes; axio-; axis; core

肩的英语翻译:

bear; low-necked; shoulder
【医】 amo-; shoulder

翻译例句

1. 但是外圈只有一个轴肩,所以轴承可以拆开。

The outer ring, however, has only one shoulder , so the bearing can be taken apart .

2. 圆轴轴肩处若采用尖角过渡,承载时将引起较大的应力集中。

If transition at the shaft collar of a circular shaft adopting closed Angle will bring biggish stress concentration as bearing load.

3. 为了获得令人满意的支持轴肩,以及住房肩膀,必须有一定的最低高度。

To gain satisfactory support both the shaft shoulders as well as the housing shoulders must have a certain minimum height.

4. 为分析搅拌头轴肩底面轮廓对材料流动的影响,分别建立了平面轴肩和凹面轴肩。

The flat and concave shoulder was set up to study the influence of the profile of concave shoulder on the flow of aluminum.

5. 轴套上设有与主轴轴肩配置的装配台阶,轴套台阶与水密封板之间形成有固定的间隙。

An assembly step matching the shaft shoulder of the mainshaft is positioned on the shaft sleeve and a fixed gap forms between the shaft sleeve step and the water-tight plate.

6. 轴肩较大的搅拌头有利于塑性金属在焊缝厚度方向上的迁移,洋葱环更易于在厚度方向上扩张。

The stirrer with bigger shoulder contributes to the transformation of plasticity in the direction of weld thickness, it is easier for onion rings to expand in the weld thickness direction.

7. 介绍了利用ANSYS软件对圆轴轴肩圆角进行优化设计的方法,在工程实际中有重要的应用价值。

This thesis introduces the method of optimal design for the circular arc transition radius of the shaft collar of a circular shaft with ANSYS, which has an important use value in engineering practice.

8. 2减速机输入轴处轴肩处未细致考虑过渡圆角的曲率半径和变化曲线使应力集中严重发生疲劳破坏。

2 the curvature radius and the change curve of the transition fillet at the shoulder of the input shaft of the reducer are not carefully considered.

9. 在综合分析断裂现象、化学成分和实际工作情况后,认为轴肩定位不完全是导致销轴断裂的主要原因。

The result shows that it is the localization incompletely of shaft shoulder which causes the fracture of pin.

10. 通过分析发现,齿根处和轴肩过渡处应力值很高,这与实际应用过程中经常发生断裂的情况是一致的。

By analyzing, the stress of teeth-root is higher, it is coherent with the actual crack condition.

11. 与轴肩挡边处于一边的沟墙61被连接于沟底深中心71处,这样一来,弯面75就与轴肩挡边在一边了。

The groove wall 61 on the side with shoulder rib is connected with the groove bottom deepest part 71 in that condition by the curved surface part 75 on the side with shoulder rib.

12. 3减速机为垂直轴形式,第一级输入轴为伞齿轮轴,在伞齿轮支承轴承处过渡轴肩处出现较严重的应力集中而发生疲劳破坏。

3 the reducer is in the form of vertical shaft, the first input shaft is the bevel gear shaft, and the more serious stress concentration occurs at the transition shaft of the bevel gear bearing.

13. 实验结果表明:随着距轴肩和搅拌针距离的增大,速度场开始减弱,焊缝金属由顶面向底面、由搅拌区向旋转区的流动也随之减弱。

The result shows that the velocity field changes with the increase of space from shoulder and stir tool and the flow of weld metal from top to bottom and stir zone to rotation zone also weakens.Www.wEntIyi.COM

14. 这将检测到大约 63 个双坐标轴空间移位,这与膝上型计算机在处于运行状态时被放在典型的单肩背膝上型计算机包中的情况一致。

This will pick up about 63 dual-axis dimensional shifts, consistent with the laptop being running while in an over-the-shoulder typical laptop bag.

15. 因为肩端是多轴性关节,可多方向自由运动,所以特定某个方向是困难的。

Because the shoulder end is a multi axis joint, it can move freely in many directions, so it is difficult to be specific in one direction.

16. 目的探讨采用预扩张颈肩背反流轴型皮瓣及颈胸皮瓣联合修复颈侧部瘢痕挛缩畸形的效果。

Objective To explore the efficacy of prefabricated expanded cervico-scapulo-dorsal reverse axial flap combined with cervico-thoracic skin flap to repair cicatricial contracture of lateral neck.

17. 胳臂和肘要弯曲,使它们随着每一步以肩为轴进行摆动。

Bend your arms at elbows. Let them swing from the shoulders with each step.

18. 以外侧脚为轴转动打开了你的髋,这同样也使你的转肩变得更容易。

Pivoting with your outside foot opens up your hips. This makes it easier to turn your shoulders sideways.

19. 臂要伸直,并保持伸直的姿式不变,以肩为轴把球拍划出弧线,在肩部的前方勾击来球。

Keeping the arm as stiff as a board, swing it in an arc-like motion from the shoulder, making contact in front of the shoulder.

20. 臂要伸直,并保持伸直的姿式不变,以肩为轴把球拍划出弧线,在肩部的前方勾击来球。

Keeping the arm as stiff as a board, swing it in an arc-like motion from the shoulder, making contact in front of the shoulder.

版权声明:问题易所有作品(图文、音视频)均来源网络,版权归原创作者所有,与本站立场无关,如不慎侵犯了你的权益,请联系我们告知,我们将做删除处理!