角接接头用英语怎么说,角接接头的英文翻译


词语导航

基本信息

词语:角接接头

繁体:角接接頭

拼音:jiǎo jiē jiē tóu

英语翻译

【化】 corner joint

分词翻译

角接的英语翻译:

【化】 corner joint

接头的英语翻译:

connect; get in touch with; joint; piece
【计】 splice
【化】 adapter

翻译例句

1. 介绍一种弯管和法兰角接接头填角焊的自动焊接装置。

An automatic CO2 welding device for elbow pipe and flange fillet weld joint is introduced in the paper.

2. 起居室和桑拿室的木质结构以鱼尾角接接头,这是典型的芬兰传统建筑系统。

The living room and sauna have a log frame with fishtail corner joints, which is a typical old Finnish building system.

3. 纵向角接接头超声冲击处理试件与原始焊态试件相比,疲劳强度提高1 73 %左右,疲劳寿命延长了3 2~ 70倍。

The fatigue strength of the longitudinal fillet welded joint specimen treated by ultrasonic peening increases by about 173% and the fatigue lifetime prolonges by 32~70 times.

4. 按目前大多数人认可的角接接头焊脚的定义,根据DL/T869—2004《火力发电厂焊接技术规程》去控制焊接尺寸,会出现焊缝有效厚度不足的问题。

The weld size was controlled according to the definition of leg on the corner joint and DL/T869—2004 (power plant welding technical regulation), which led to the effective thickness was insufficient.

5. 试验分析说明铝合金5083纵向角接板焊接接头名义应力和热点应力疲劳s - N曲线试验数据拟合斜率为5。

The test analysis shows that the fitted slope of test data to nominal stress and hot spot stress S-N curves for aluminum 5083 welded joint with longitudinal fillet welded gusset is 5.wWW.wEntiYi.coM

6. 研究了在胶瘤中嵌入三角形金属楔块对单搭接接头强度和应力分布的影响,结果表明,金属楔块能显著提高接头的强度。

The influence of embedded trilateral cross-section metal bar in the fillet on the strength and stress distribution of single lap joints was discussed.

7. 运用固有应变法研究了六个固有应变分量分别对搭接接头焊接角变形的影响。

The effect of each inherent strain component on the angular distortion of the lap joint is studied using inherent strain method.

8. 这些元素可以以不同方式组合在一起,例如:一个搭接接头可能用角接、塞焊和缝焊固定,一个丁字接头可以用一个搭接或槽焊来完成。

The elements can be put together in various ways. For example, a lap join may be held by a fillet, plug, or slot weld, and and a tee joint by a fillet or groove weld.

9. 以T形焊接接头为算例,结合热弹塑性有限元法和映射应变分量法,研究了角焊缝角变形的产生机制。

The conception of deformation angle of helix pre-former is introduced and process parameters are analyzed with math regression method.

10. 对接焊缝可评定全焊透和部分焊透对接焊缝和角焊缝,当角焊缝是产品的主要焊接接头形式时,需要用角焊缝试验评定。

Butt welds qualify full and partial penetration butt welds and fillet welds. Fillet weld tests shall be required where this is the predominant form of production welding.

11. 对接焊缝可评定全焊透和部分焊透对接焊缝和角焊缝,当角焊缝是产品的主要焊接接头形式时,需要用角焊缝试验评定。

Butt welds qualify full and partial penetration butt welds and fillet welds. Fillet weld tests shall be required where this is the predominant form of production welding.

版权声明:问题易所有作品(图文、音视频)均来源网络,版权归原创作者所有,与本站立场无关,如不慎侵犯了你的权益,请联系我们告知,我们将做删除处理!