
词语导航
基本信息
词语:阀帽
繁体:閥帽
拼音:fá mào
英语翻译
【化】 bonnet
相关词条
1.valvebonnet分词翻译
帽的英语翻译:
cap; hat【化】 cap
【医】 cap; cowl; galea; headcap; pileus; pilleus
翻译例句
1. 穿过阀帽的通道(34)可用于检验通过这种密封件是否泄漏。
A passage through the bonnet (34) may be used to test for leakage past such seal.
2. 阀体-阀帽的焊接工艺是采用完全自动化的mig焊接设备进行的。
The body - bonnet welds are made on fully automatic MIG Welders.
3. 压力界限通过密封-楔板,阀体-阀帽连接和动负载填料腔来保证。
The pressure boundary is secured by a seal-welded body-bonnet joint and a live-loaded packing chamber.
4. 备用密封件是阀帽(12)内主阀杆密封组件(20)的二级密封。
The backup seal is secondary to the main stem seal assembly (20) in the bonnet (12).
5. 旋松阀帽中间的内六角螺丝,并且提起阀帽,正好足够拿走旧阀膜。
Unscrew the Allen screw in the middle of valve cap and lift up the cap just enough to pick up the old diaphragm.
6. 将阀帽总装拆离阀腔,采用推针取出四个部分的推力环,拆卸变得简便易行。
Easy dismantling is made possible by dropping the bonnet assembly into the body cavity and driving out the four-segmental thrust rings by means of a push pin.
7. 装配时始终打开阀帽直到一次装入所有要求安装的配件可使阀体和阀帽良好配合。
The body and bonnet are best joined by holding the bonnet assembly open end up and dropping all required items into place one at a time.
8. 碳钢,合金钢或不锈钢,压力密封或螺栓阀帽用于焊接在螺栓阀帽阀门上阀座的设备。
Carbon, Alloy or Stainless Steel, Pressure seal or Bolted Bonnet Provision for seal Welding on Bolted Bonnet Valves.
9. 阀体和阀帽连接部位经过精密机加工。密封垫材料请参阅第3页,详细内容参阅第13页。
Body and bonnet joint accurately machined. Gasket materials on page 3, details on page 13.
10. 低温设备仪表在线阀门的阀帽和填料箱应为加长阀帽型或伴热型(必要时),从而避免阀杆结冰。
The bonnet and packing box of low temperature service instrument in-line valves shall be extended bonnet type or heat traced, if necessary, to avoid freezing of valve stems.
11. 我们现在能够提供标准铸钢螺栓阀帽闸阀和截止阀,这些阀门都通过符合EPA短时排放规定要求的鉴定测试。
Velan now offers standard cast steel bolted bonnet gate and globe valves qualification tested for compliance with EPA fugitive emissions regulations.
12. 清洗:检查或更换磨损的阀瓣,断开控制管道的连接,采用钝工具和锤子敲击阀帽上的接片,然后旋松阀帽螺纹。
To Clean: Inspect or replace worn valve disc, disconnect control pipe and unscrew bonnet from valve body using blunt tool and hammer on bonnet lugs.
13. 曲柄轴箱通风阀和配有废气帽的空气污染控制阀(的使用)对减少挥发性有机混合物释放有积极作用。
The positive crankcase ventilation valve and gas caps with air-pollution control valves reduce volatile organic compound loss.
14. 安装到瓶帽孔顶部的阀的特征在于:它具有小通风帽(3),该帽容 纳倒转的柔性容器(4)。
A valve attached to the top of the cap port is characterised in that it has a small ventilated cap (3) housing an upside-down flexible vessel (4).
15. 安装到瓶帽孔顶部的阀的特征在于:它具有小通风帽(3),该帽容 纳倒转的柔性容器(4)。www.WENTIYi.cOM
A valve attached to the top of the cap port is characterised in that it has a small ventilated cap (3) housing an upside-down flexible vessel (4).
版权声明:问题易所有作品(图文、音视频)均来源网络,版权归原创作者所有,与本站立场无关,如不慎侵犯了你的权益,请联系我们告知,我们将做删除处理!
