螺纹高度用英语怎么说,螺纹高度的英文翻译


词语导航

基本信息

词语:螺纹高度

繁体:螺紋高度

拼音:luó wén gāo dù

英语翻译

【机】 height of thread

分词翻译

螺纹的英语翻译:

screw thread; whorl; worm
【机】 screw thread; thread

高度的英语翻译:

altitude; height; high; highly; highness; stature; tallness
【计】 H
【化】 height
【医】 height; super-

翻译例句

1. 该方法可测量螺纹的锥度、螺距、螺纹夹角和螺纹高度,测量精度可以满足工业测量要求。

The equations for thread taper, thread pitch, thread angle and height of thread can be derived on the base of fitted lines, which are accurate enough to meet the needs of industrial measurement.

2. 内径千分尺、千分尺、塞规、螺纹规、数显卡尺、高度尺等检验工具。

Inside diameter micrometer micrometer plug gauge thread gauge digital calipers height gauge and other testing tools.

3. 主要提出以下观点:锅炉吊杆用螺母的高度与螺纹公称直径之比不宜小于1。

Presents the following viewpoints:the radio between the height of the nut for boiler hanger rod and the diameter of screw shall not be less than 1.

4. 该装置是用公制螺纹npt和几个高度集成的。

The apparatus is highly integrated with NPT and several metric threads.

5. 阿钢螺纹安装支架和多个安装点使计划64高度通用的解决方案,音响系统。

A steel mounting bracket and threaded multiple mounting points makes the Programme 64 a highly versatile sound systems solution.

6. 经分析得出:事故原因是减压阀阀座和阀盖的连接螺纹接触高度过小,强度不足,导致螺纹连接失效。

The screw joint of the reducer bonnet and body was concluded as the failure position because of its small contact height.

7. 通过螺纹的联接来调整总杯子的高度和容量。

The height and capacity of the screwed cup can be regulated by screw joint.

8. 肮 该系列产品是广泛应用于石油行业的高精密仪器,共有20多个品种,主要用于石油油管、套管、钻杆锥形螺纹的锥度、螺距、高度等单项参数的测量。

These high precision instruments are more than 20 kinds and widely used for oil industry to measure the monomial parameters of taper, pitch and height screw for oil pipe, canola and drill shank.

9. 按图纸标高,用水准仪校准到统一高度,按位置记录并收紧螺纹千斤顶。

Screw jacks are put on the seat pads and adjusted to the same height using a leveling instrument. Then the screw jacks shall be fixed tightly and their positions recorded.

10. 该关系式可对外螺纹铜管凸筋高度进行预测与控制,对外螺纹铜管冷拔工艺的制订具有参考价值。

This relationship can be used to forecast and control the fin-height of the outer-spiral-fin tube, and it has referenced value for the working-out of the technics for cold-drawn outer-spiral-fin tube.

11. 利用多元线性回归建立了冷拔外螺纹铜管凸筋高度与坯料壁厚之间的经验关系式。

The experience relationship between fin-height and rough tube wall-thickness for cold-drawn outer-spiral-fin tube is established with many-membered Iinear regression in this paper.WWw.wenTIYi.COM

12. 利用多元线性回归建立了冷拔外螺纹铜管凸筋高度与坯料壁厚之间的经验关系式。

The experience relationship between fin-height and rough tube wall-thickness for cold-drawn outer-spiral-fin tube is established with many-membered Iinear regression in this paper.

版权声明:问题易所有作品(图文、音视频)均来源网络,版权归原创作者所有,与本站立场无关,如不慎侵犯了你的权益,请联系我们告知,我们将做删除处理!