
词语导航
基本信息
词语:内摆线
繁体:內擺線
拼音:nèi bǎi xiàn
英语翻译
【机】 hypereutectoid
分词翻译
内的英语翻译:
inner; inside; within
【医】 end-; endo-; ento-; in-; intra-
摆线的英语翻译:
cycloid
【电】 cycloidWww.wenTiYI.Com
翻译例句
1. 绕着另一个圆圈滚转的圆圈;产生外摆线或内摆线。
A circle that rolls around another circle; generates an epicycloid or ".
2. 根据内摆线的形成原理,设计出一种齿轮无级变速器。
Based on the principle of the formation of hypocycloid, a kind of stepless gear speeder has been designed.
3. 在S195柴油机结构基础上,完成新型内摆线能量转换机构结构设计。
And its structural design was completed based on structure of a S195 type diesel engine.
4. 主要从事新型无侧压无连杆内摆线行星齿轮内燃机的研制开发和经济管理软件的开发。
Mainly engaged in a new type of lateral pressure without cycloidal gear linkage within the internal combustion engine research and development of economic management and software development.
5. 论述波式滚动活齿传动内齿轮齿廓曲线的两种选择:内摆线的等距曲线、密切圆弧曲线的理论成因。
The text introduces the two choices of inner gear profile curve of the rolling gear drive and the theoretical reasons of the equidistance curve of inner cycloid and the close an; curve.
6. 摆线齿形的内啮合齿轮泵又叫做摆线转子泵,泵中的小齿轮和内齿轮只相关一个齿,因此这种内啮合齿轮泵不需要设置隔板。
Cycloidal tooth profile of the internal gear pump, also called cycloidal rotor pump, pump the small gear and internal gear only related a tooth, so the internal gear pump do not need to set partition.
7. 内啮合齿轮泵有两种齿形即:渐开线齿形和摆线齿形。
Internal gear pump has two kinds of tooth profile namely: involute profile and cycloidal tooth profile.
8. 对一种新型圆弧摆线内啮合转子泵进行了研究。
A new type of arc cycloidal internal meshing rotary pump was studied.
9. 新型摆线凸轮活齿传动是一种内齿轮齿廓为摆线及其等距线的二齿差活齿行星传动。
The new cycloid cam sliding tooth transmission is a two-teeth difference sliding tooth planetary gearing with cycloid internal gear.
10. 为了限制内啮合摆线转子压缩机中外转子绕内转子公转的趋势,在外转子上施加一个支撑力,对支撑力的位置进行了详细分析。
The outer rotor has the trend of revolution along the inner rotor and this trend must be overcome by the cylinder via the action of a support force in an internal-meshing rotary cycloid compressor.
11. 内啮合摆线转子齿轮油泵的齿形对泵的加工、性能(如:流量、脉动、噪声)等有很大的影响。
The gear form of internal gearing cycloidal gear pump has important influence on machining and characteristics of pump, such as flow rate, fluctuation rate and noise etc.
12. 研制了用于加工摩托车离合器外环内孔表面的三键圆弧摆线拉刀,分析了拉刀的结构特点和设计、制造要点。
The three spline broach with radius pendulum profile is developed to broach the internal surface of motorcycle clutches.
13. 在保证逼近误差限制在允许范围内的前提下,以加工效率最高为目标,提出了确定摆线参数的优化算法。
On condition that the approximate error was in allowable range, the optimization algorithm to fix cycloid parameters was given for the objective of the highest machining efficiency.
14. 双摆线齿轮减速器是应用外摆线内等距曲线作为齿轮齿廓曲线的一种新产品。
The double cycloid gear reducer is a kind of new product which applies external cycloid internal equidistant curve as the curve of gear flank profile, It is characterized by;
15. 双摆线齿轮减速器是应用外摆线内等距曲线作为齿轮齿廓曲线的一种新产品。
The double cycloid gear reducer is a kind of new product which applies external cycloid internal equidistant curve as the curve of gear flank profile, It is characterized by;
版权声明:问题易所有作品(图文、音视频)均来源网络,版权归原创作者所有,与本站立场无关,如不慎侵犯了你的权益,请联系我们告知,我们将做删除处理!
