
词语导航
基本信息
词语:螺栓应力
繁体:螺栓應力
拼音:luó shuān yīng lì
英语翻译
【化】 bolt stress
分词翻译
螺栓的英语翻译:
【电】 bolt
应力的英语翻译:
stress
【化】 stress
【医】 stress
翻译例句
1. 论文对超声螺栓应力测量原理,超声螺栓紧固力测试仪设计进行了系统研究。
The thesis lucubrated the principle of ultrasonic bolt tension measurement and design of ultrasonic bolt tension measurement instrument.
2. [S-1]在螺栓被初步紧固之后,由于垫片的缓慢蠕变或松弛,特别是采用的是“比较软的”垫片材料,则螺栓应力的下降是可能的。
It is possible for the bolt stress to decrease after initial tightening, because ofslow creep or relaxation of the gasket, particularly in the case of the "softer" gasket materials.
3. 在拉应力和应拉力交替的作用下,强度相对较低的螺栓会先产生裂纹,进而发生疲劳断裂。
Under the action of tensile stress and tensile stress, the bolt with relatively low strength will crack first, and then the fatigue fracture will occur.
4. 这样,在螺栓张力相同的情况下,缩小后的窄光滑面的压紧应力就会增大。
So, in the same bolt tension narrow narrow smooth after the pressure stress increases.
5. 如果附加弯矩产生的应力过大,螺栓便会断裂。
If the stress produced by the additional bending moment is too large, the bolt will break.
6. 在此奥氏体螺栓材料经过碳化溶液处理和应力硬化处理,因此归在ASTMA193类别2里。推荐采用相应材料的ASTM A194螺母。
Where austenitic bolting materials have been carbide solution treated and strain hardened, they are designated Class 2 in ASTM A193. ASTM A194 nuts of corresponding material are recommended.
7. 认为主要原因是螺栓在长期服役中受交变应力引起疲劳失效所致。过热蒸汽介质对疲劳失效有影响。
It revealed that alternating stress in long time cause the bolt fatigue failure, meanwhile the failure process was also effected by superheating steam.
8. 通过计算分析,螺栓的疲劳应力稍偏高。
By analysis, bolt fatigue stress is marginally high.
9. 应用接触有限元方法,对螺栓联接结构进行了应力分析。
The contact finite element method is used in present paper to analyze stress of bolt connection structure.
10. 介绍了一种应用于大规格螺纹预紧的新型结构FROMO预紧螺母的结构设计,该结构螺栓只承受纯拉应力。
The design of a new pre-tensional structure (FROMOpreload nut) applied in the large size of screw thread was introduced, the pre-load bolt is only beared with the pure tensile stress.
11. 结果表明,冷扩张过程所引入的切向残余压应力能保持足够的强度,以对钢轨螺栓孔起到显著的防裂和止裂作用。
It is concluded that, the residual stress induced by cold expansion can maintain enough strength to prevent and retard fatigue crack initiation and growth in rail bolt hole.
12. 本文对M27和M24两种直径高强度螺栓进行了复合应力系数测定和预拉力损失试验。
The composite stress factor and pre-tensile force loss of the two diameter high strength bolts of M27 and M24 are experimentally determined in the paper.
13. 分析结果表明,该连杆螺栓早期疲劳断裂的原因是由于杆部与头部的过渡圆弧处产生的应力集中所导致的。
Analysis results indicate that the arc transition area between rod and head is easy to produce stress concentration, which results in earlier fatigue failure.
14. 认为用估算螺栓工作时的最大预紧应力的方法,对防止埋头螺栓疲劳断裂再次重复发生有一定的参考价值。
We think that the method of estimating maximal pre-applied stress of the working bolt can provide a reference for preventing further fatigue fracture of boxter bolts.
15. 结果表明,螺栓的预紧应力接近材料的断裂强度。
The results suggest that the stress is close to the breaking strength.WwW.WeNTiYI.COM
16. 螺栓扭矩增大,接头区钢轨轨腰拉力、夹板应力、螺杆内应力都会增大,而钢轨位移会随着螺栓扭矩的增大而减小。
As the bolt tension increase, the tension of rail web, stress of joint bar and stress of joint bolt would increase accordingly, but the displacement of rail would become smaller.
17. 为了确保飞轮螺栓连接的可靠性,采用接触分析法对螺栓进行了应力分析。
In order to ensure the reliability of flywheel bolt connection, stress analysis of bolt is performed using contact analysis method.
18. 本文将反应堆压力壳的球顶盖、上下法兰、螺栓、筒体及双道O形环作为一个超静定系统进行了应力和变形分析。
The reactor pressure vessel composed of spherical top and lower heads, upper and lower flanges, bolts, cylinder and two O-rings, as a static indeterminate system has been studied.
19. 本文着重分析了离散分布的螺栓及螺栓孔对筒体端部应力的影响,对筒体端部的应力计算提出了一个更接近实际的计算模型。
This paper focuses on the effects of the distributed bolts and bolt-holes on the shell flange-end bending stress, and suggests a more practical calculation model on shell-end stress.
20. 根据螺栓的轴向应力与超声波传播时间变化率的关系,作者研究了一种可直接测量螺栓轴向应力的仪器。
On the basis of relationship between bolt axial stress and rate of change in ultrasonic wave transmission time, the author has developed a device to directly measure axial stress in bolts.
21. 在高温环境下有紧密性要求的螺栓联接,在设计时应考虑应力松弛。讨论了关于应力松驰问题的计算思路和解决方法。
Stress relaxation should be taken into consideration while designing tight bolt connection under a high temperature. The paper discusses the calculation thought and solution about stress relaxation.
22. 这样,在螺栓张力相同的情况下,缩小后的窄光滑面的压紧应力就会增大。
Thus, under the same bolt tension, reduce narrow smooth surface after the compressive stress will increase.
23. 采用经典的三维光弹性实验技术和新兴的焦散线实验方法,分别研究了螺栓联结件的三维接触应力及其接触影响区域。
The 3-d contact stress in bolted joint parts and its contact coverage are investigated experimentally with the photoelastic method and the newly developed caustics method.
24. 简要介绍武汉白沙洲大桥主桥上部结构的钢箱梁、高强螺栓、预应力混凝土箱梁、斜拉索的施工工艺和质量控制措施。
Construction technology and quality control measures for steel box girder, high-strength bolt, prestressed concrete box girder and inclined cable are briefly introduced.
25. 应用螺栓-垫圈应力理论对FRP结构搭接点预紧力进行了研究。
The pretightening force of FRP construction bolt joint has been researched in the theory of bolt washer stress.
26. 为确保钢结构工程的可靠性和安全性,必须严格控制连接螺栓的预紧力,必要时还要在线监测螺栓工作应力。
To guarantee the reliability and security of the steel construction, the clamp load of the joint bolt should be under strict control, sometimes even the tension of the bolt should be measured on-line.
27. 冷作强化非调质钢螺栓经时效处理可以稳定组织、提高强度、降低残余应力。
Aging treatment is performed for microalloyed steel for cold hardening bolt, which can stabilize its microstructure, enhance its strength and reduce its residual stress.
28. 螺栓预紧力的大小对垫片压紧应力的大小及分布有重要影响。
The bolt preloading also has important influence on the distributions of compressive stresses of the two gaskets.
29. 螺栓预紧力的大小对垫片压紧应力的大小及分布有重要影响。
The bolt preloading also has important influence on the distributions of compressive stresses of the two gaskets.
版权声明:问题易所有作品(图文、音视频)均来源网络,版权归原创作者所有,与本站立场无关,如不慎侵犯了你的权益,请联系我们告知,我们将做删除处理!
