状态命令用英语怎么说,状态命令的英文翻译


词语导航

基本信息

词语:状态命令

繁体:狀態命令

拼音:zhuàng tài mìng líng

英语翻译

【计】 status command

分词翻译

状态的英语翻译:

state; condition; fettle; position; predicament; status
【计】 behaviour; S; ST; state; status; transient regime
【医】 asiminine asis; condition; etat; sirupus ferri jodati; state; status
【经】 state

命令的英语翻译:

order; command; appoint; dictate; imperative; instruct
【计】 command; GO TO command GOTO

翻译例句

1. 只有在每一个状态都是相对和明确的情况下才使用状态命令。

Use state menu commands only when both states are clearly opposite and unambiguous.

2. 状态选择一个状态命令激活一个属性并让其他的状态等待激活。

Stated items Selection of a stated command activates a property and leaves other properties available for activation.

3. 状态命令显示了池中的情况,以及哪个硬盘驱动器似乎出故障了。

The status command shows what is happening in the pool and which hard drive seems to be failing.

4. 通信协议保证了群控主机和各电梯正常通信,本文设计了群控主机和各电梯之间的通信协议,包括消息的格式、状态命令、控制命令等。

This paper designs the communication protocol between group control host and elevators which contain message format, state commands, control commands and so on.

5. 视图模型导入对话框,然后给予状态改变或是命令来触发对话框服务。

The view model can import the dialog, then based on some change in state or a command, trigger the dialog service.

6. 在街上的士兵们是否处于无命令状态或者是挑衅仍不明确。

It was unclear whether the soldiers in the streets were operating without orders or in defiance of them.

7. 提交的状态也可以从此命令得到。

The status of the delivery can be obtained with this command as well.

8. 否则,如果当前状态不匹配已记录的状态,则运行指定的命令。

Otherwise, if the current state does not match the recorded state, run the command specified.

9. 类似地,||控制操作符分隔两个命令,并且仅当第一个命令返回非零退出状态时才运行第二个命令。

Similarly, the || control operator separates two commands and runs the second command only if the first command returns a non-zero exit status.

10. 由于查明伏击的那个夜晚,他处于酒醉状态,命令规定对他不予追究,释放了他,他恢复了自由。www.wEntiyi.COm

An order of nolle prosequi, founded on his well authenticated state of intoxication on the evening of the ambush, had set him at liberty. He had taken to his heels.

11. 状态模式类似于命令模式,但是意图截然不同。

The state pattern is a similar to the command pattern, but the intent is quite different.

12. 命令的返回状态可用于确定特定的命令是否正确运行,或者是否生成了某种类型的错误。

The return status from a command can be used to identify whether a particular command ran correctly, or whether it generated some sort of error.

13. 函数编程方式很容易理解,但是如果您习惯了过程序和关注状态的命令式语言,可能不太容易适应它。

The functional programming approach is easy to understand, but can be difficult to apply if you are used to the more procedural and state-focused imperative languages.

14. 运行清单31中的命令,列示代理IBMESBBRK的状态。

Use the command in Listing 31 to list the state of the broker IBMESBBRK.

15. 可以用以下命令检查每个实例的状态。

You can check the status of each instance with the command.

16. 还可以选择使用gitstatus命令查看新项目的状态。

Optionally, use the git status command to check the status of your new project.

17. 停止并重新启动队列守护进程之后,使用lpstat命令检查队列状态。

After stopping and restarting the queue daemon, check the queue status using the lpstat command.

18. bta命令对处于某种特定状态的所有进程执行回溯。

The bta command does a traceback for all processes in a particular state.

19. 要检查wpar状态,请使用lswpar命令(请参见清单2)。

To check the status of the wpar, use the lswpar command (see Listing 2).

20. 然后处理notify. config文件以载入在达到每种状态时要运行的命令。

The notify.config file is then processed to load the commands to run upon each state being reached.

21. 它将打印状态信息并将sleep命令发送给SIGINT信号。

It prints a status message and sends the sleep command a SIGINT signal.

22. 单击gui的按钮组件后,直接从数据库中检索某个特定命令的状态,如清单2所示。

When the GUI"s button component is clicked, a particular order"s status is retrieved directly from the database, as shown in Listing 2.

23. 执行以下命令显示Sendmail守护进程的状态。

Execute the following command to display the status of the Sendmail daemon.

24. 运行以下命令检查IPSec设备的状态。

Run the following command to check the state of the IPSec devices.

25. 同时注意,追踪大文件状态的dirstate命令,在Mercurial 2.0中目前是被限制在2Gb以内,但有希望在2.0发布之后会发布补丁。

Note that the dirstate command, which tracks the state of largefiles, is currently limited to 2Gb in Mercurial 2.0, although there are hopes for a fix post the 2.0 release.

26. CLIshow命令用于显示状态信息,清单1显示的是showcpu命令,它将会提供与WebGUI中一样的数据表格。

The CLI show commands are used to display status information, and Listing 1 shows the show CPU command, which provides the same table of data shown in the Web GUI.

27. 要查看ha系统状态,运行sudo crm_mon命令。

To see the HA system status, run the sudo crm_mon command.

28. 可以使用oncheck - pttest:nagaraju . tab命令检查alter模式状态。

You can check the alter mode status using the oncheck -pt test: nagaraju.tab command.

29. 可以使用oncheck - pttest:nagaraju . tab命令检查alter模式状态。

You can check the alter mode status using the oncheck -pt test: nagaraju.tab command.

版权声明:问题易所有作品(图文、音视频)均来源网络,版权归原创作者所有,与本站立场无关,如不慎侵犯了你的权益,请联系我们告知,我们将做删除处理!