开启位置用英语怎么说,开启位置的英文翻译


词语导航

基本信息

词语:开启位置

繁体:開啟位置

拼音:kāi qǐ wèi zhì

英语翻译

【化】 open position

分词翻译

开启的英语翻译:

open; turn on; unlock; unseal
【计】 turn-on

位置的英语翻译:

place; position; locality; location; situation; station
【计】 LOC; location; POS; position
【医】 P; position; Sisyrinchium galaxioides; situs
【经】 position

翻译例句

1. 把PCV阀固定在开启位置即最大流量位置。

The PCV valve sticks in the open, maximum-flow position.

2. 无法开启位置,可能你没有开启该档案的权限。

Could not open location; you might not have permission to open the file.

3. 排气螺丝应该位于开启位置,并且在焊接时要有遮盖以免被火源烧到。

The purge screw should be in the open position and shielded from direct heat when soldering.

4. 当手轮象开启位置旋转时,上阀杆离开横膈膜,弹簧推动下阀杆离开阀座。

When the handwheel is rotated toward the open position the upper stem is moved away from the diaphragms allowing the spring to push the lower stem away from the seat.

5. 当手轮象开启位置旋转时,上阀杆离开横膈膜,弹簧推动下阀杆离开阀座。

The lower stem is encased in a spring which forces the stem away from the seat when the valve is opened.

6. 用于当阀门安装在高处或无法靠近的地方时,但是有需要经常观察阀门开启位置的情况。

Used when the valve is mounted in high or out-of-reach locations, but frequent monitoring of the valve position is required.

7. 冰冻气候预防措施:测试管道系统后,法门应该处于开启位置,使得能够实现完全排泄。

FREEZING WEATHER PRECAUTION: Subsequent to testing a piping system, valves should be left in an open position to allow complete drainage.

8. 装置刚启动时,管道出现低温冷凝水,膜盒内的液体处于冷凝状态,阀门处于开启位置。

When the device just starts, there appears condensate with low temperature in conduits and the liquid in the bellows is in the condensed state. The trap is turned on.

9. 不管是在阀门开启位置,还是关闭位置,阀杆和密封面有阀杆盖帽的保护,能防止污物入内,防止腐蚀。

The valve stem and sealing surfaces are completely protected from dirt and corrosion by the stem cap, whether the valve is in an open or closed position.

10. 一旦确定正确的流量设置,则将记忆止动装置朝着指示器板的开启位置顺时针方向旋转,直到记忆止动环触到指示器板为止。

Once correct flow rate setting has been established, slide memory stop clockwise towards open side of indicator plate until memory stop ring hits indicator plate.

11. 在连接单个管套接阀门的固定端口时,将球体放置在开启位置,使得阀内部件能够得到干燥并避免底漆或液状粘固剂接触到阀内件。

When joining the fixed end of a single union valve, place the ball in the open position to allow for proper drying and to avoid primer or solvent cement contacting internal components of the valve.

12. 如果流体流速压力无法将阀门支撑在一个较大的开启度并保持在稳定的开启位置,则阀瓣和相关的运动部件可能会处于一种持续振动的状态。

The disc and associated moving parts may be in a constant state of movement if the velocity pressure is not sufficient to hold the valve in a wide open and stable position.

13. 开启发动机时,一定要使汽车的离合器处于空挡位置.

When you start the engine, you must see to it that car is inneutral.

14. 把排气阀固定在它开启的位置。

Lock the exhaust valve in its open position.

15. 他是利用流体速度压力来开启和保持在开启的位置,并利用重力的作用来关闭。

They are opened and sustained in the open position by the force of velocity pressure, and closed by the force of gravity.

16. 转距臂会将开关设置在开启和关闭的位置。

The torque arm will actuate the switches in open and closed positions.

17. 检查阀门各部位是否有松动现象,对阀门进行手动开启、关闭一个周期是否有异常现象,同时检查阀门的启闭位置是否准确。

Check the valve parts before installation. Open and close the valve by hand for a period check the open-close position of the valve gate.

18. 必须把阀门开到完全开启的位置,以提供完全的流通。

It is not necessary to open this valve to the full open position to provide full flow to the process.

19. 你可以选择以目前的位置去进入新一年,也可以选择开启并进入这条通道,创造并更新你的意识结构和理解力,正是它们驱动着你的经历。

You can pass into this new Year using your current positioning or you can open into this passage and create and renew your framework of intentions and understanding which generates your experience.

20. 按下“开启”或“闭合”按纽,幕体到达行程终止位置时,行程终止开关将被激活时,大幕机停止运行。

Press "Open" or "Close" button, while reaching stop position, stop switch will be activated and the proscenium curtain machine will stop running.

21. 不管阀门是在开启或是关闭位置,手轮总是处在相对于阀体的同样的位置。

The hand wheel is always in the same position relative to the valve body regardless of whether the valve is in the open or closed position.wWW.wEntIyi.COm

22. 内部安装的固体状态定位器主板能够精确控制阀门从开启到关闭的各种位置。

An internally mounted, solid state positioner board accurately controls valve position from open to close.

23. 通过改变执手手柄的位置而实现各种开启功能,操作方便、简单耐冲击。

By changing the position of the handle and the handle is turned to achieve a variety of functions, easy operation, simple impact resistance.

24. 通过改变执手手柄的位置而实现各种开启功能。

Various opening functions can be achieved by changing the location of the hand grip.

25. 点火正时装置:触点必须能够在活塞处于气缸中相关位置时,按时关闭和开启。

Ignition timing devices. The contact points must be timed to close and open in proper relation to the piston positions in the cylinders.

26. 点火正时装置:触点必须能够在活塞处于气缸中相关位置时,按时关闭和开启。

Ignition timing devices. The contact points must be timed to close and open in proper relation to the piston positions in the cylinders.

版权声明:问题易所有作品(图文、音视频)均来源网络,版权归原创作者所有,与本站立场无关,如不慎侵犯了你的权益,请联系我们告知,我们将做删除处理!