肋内的用英语怎么说，肋内的的英文翻译

词语导航

基本信息

词语：肋内的

繁体：肋內的

拼音：lèi nèi de

英语翻译

【医】 intracostal

分词翻译

肋的英语翻译：

costal region; rib
【医】 costa; costae; costo-; rib

内的英语翻译：

inner; inside; within
【医】 end-; endo-; ento-; in-; intra-

翻译例句

1. 此时需要设置抵抗膜面内力的构件，该构件可以是管状的金属构架，也可是薄膜气肋，即：内充高压气体而具有一定抗弯刚度的管状。

At this point, it is necessary to set up the component to resist the internal force of the film surface, which can be a tubular metal frame, but also a thin film gas rib.

2. 在30- 40秒内，瘫痪就开始侵袭手指、脚趾以及眼睛上的小的肌肉以及肋肌横膈膜。

Within 30 to 40 seconds paralysis begins to invade the small muscles of the fingers, toes, and eyes and then the inter costal muscles and diaphragm.

3. 在30 - 40秒内，瘫痪就开始侵袭手指、趾以及眼睛上的小的肌肉以及肋肌横膈膜。

Within30 to40 seconds paralysis begins to invade the small muscles of the fingers, toes, and eyes and then the inter costal muscles and diaphragm.

4. 出口挡板对颗粒的MRT具有十分显著的影响，而不同纵肋和环肋组合的内构件对MRT的影响主要取决于窑出口处环肋的高度；

The exit dam has a significant effect on MRT, while the influence of internal structure consisting of various longitudinal ribs and circular ribs is mainly dependent on the height of circular ribs.

5. 达味遂跑过去，站在那培肋舍特人身上，拿起他的刀，从鞘内拔出，杀了他，砍下了他的头。

He ran, and stood over the Philistine, and took his sword, and drew it out of the sheath, and slew him, and cut off his head.

6. 采用数值模拟的方法，研究了流道内上下两肋片均布置有涡产生器的扁管管片式散热板芯的传热与阻力特性，并与流道单面布置涡产生器的换热板芯进行了对比。

The characteristic of heat transfer enhancement and the fluid flow of the fiat tube bank fin exchanger which has vortex generators on both sides of the fin were investigated by using numerical method.

7. 水在特殊结构内的改向和模肋式螺旋导向促成水的湍流，加大了吸收热量的能力。

The water onflow can be made by the direction changing and rib like spirals guide it can strength the ability of heat absorption.

8. 本文对网格式肋化内冷通道在静止状态下的强化传热与流动阻力特性进行了实验研究。

An experimental investigation on the flow and heat transfer characteristics in rectangular channel with internal netted rib turbulators is conducted.

9. 提出考虑材料与几何双重非线性的钢管混凝土肋拱面内受力的计算方法并编制了有限元程序。

A method is presented to analyze the behavior of concrete-filled steel tubular (CFST) arch, which considers the material and geometric nonlinear property, and a finite element program.

10. 采用三维内肋管强化传热技术，可以达到降低水套炉的金属耗量和提高热效率的目的。

The 3-D inner gilled tube strengthening heat transfer technology can be used to reduce the metal consumption and increase the thermal efficiency.

11. 对三种微混合器混合性能进行对比，得出内肋型微混合器在各种速度条件下的混合性能要优于其它两种微混合器。

Mixing performance of three type of micromixer had been compared. The results showed that: Mixing performance of internal ribbed micromixer is superior to the other two Micromixer.

12. 本文介绍了试验的情况，分析了模型肋拱面内受力全过程的性能，并初步探讨了其面内极限承载力的简化计算方法。wWw.weNTiyi.cOm

The mechanic behavior of CFST rib arch under in-plane load is studied. The simplified methods to calculate the structure"s in-plane ultimate strength are discussed as well.

13. 本文研究还首次发现在层流区，随着雷诺数的增加，肋叉排三维内肋管和光管的换热特性曲线会出现一个交点即换热有效折点。

In this paper, increase with Reynolds number, we first find that 3-d IFT with staggered arrangement fins and smooth tube"s heat transfer characteristic curve will have a point of intersection.

14. 缝隙后的动量掺混在一段区域内也具有三维性，其大小受雷诺数和缝宽—肋宽比的影响较大。

The point where the difference becomes 0 is affected by the Reynolds number and the ratio of slot"s width to rib"s width.

15. 本文所研究的三维内肋管就是应用于各种换热器中单相强迫对流换热的新型强化传热管。

In our studies, three-dimensional internally finned tube (3-d IFT) is a type of new heat transfer enhanced tubes which can be used to enhance single-phase forced convective heat transfer inside tube.

16. 所述内管是光管、螺纹管、内肋管或带有扰流片的管子。

The inner tube is a light tube, a screw tube, an inner rib tube or a tube with a spoiler.

17. 所述内管是光管、螺纹管、内肋管或带有扰流片的管子。

The inner tube is a light tube, a screw tube, an inner rib tube or a tube with a spoiler.