轴承油用英语怎么说,轴承油的英文翻译


词语导航

基本信息

词语:轴承油

繁体:軸承油

拼音:zhóu chéng yóu

英语翻译

【化】 bearing oil

分词翻译

轴承的英语翻译:

bearing
【化】 bearing

油的英语翻译:

paint; fat; grease; oil
【化】 oil
【医】 elaeo-; eleo-; oil; Ol; olea; oleo-; oleum

翻译例句

1. 无量纲轴承油膜力的表达式中考虑了滑油粘性力的作用。

The influence of viscous force is considered while establishing nondimensional oil film force.

2. 啊电力工业:高压变压器油冷却,发电机轴承油冷却等。

The electric power industry: high voltage transformer oil cooling, oil cooling generator bearing, etc. 7.

3. 参照国内外轴承油的质量标准,确定了研制品的质量标准。

Reference the standard quality of Bearing oils of civil and foreign, define the standard quality of the formulate.

4. 介绍了摩根型无扭高速线材连轧机用460号油膜轴承油的性能及工业使用试验结果。

The performances and the results of service test of 460 filmatic bearing oil used for morgan type no-twist wire rod mills at high speed were presented.

5. 以深度精制的石蜡基馏分油为基础油,添加了各种添加剂,制备了轴承油l - FD68。

The Bearing oil L-FD68 were formulated from base oil obtained by deep-refining paraffinic crude and doped with various additives.

6. 介绍了基于可编程序控制器和工业显示触摸屏的大型贯流式水轮发电机组轴承油系统控制装置的主要设计特点。

The control device for large bulb unit bearing oil system is ba sed on the programmable logic controller and programmable operator interface.

7. 介绍了油膜轴承油国外现状和国内水平及其应用简况,分析了油膜轴承用油国产化的人为障碍及今后国产化的希望。

The present status abroad, domestic level and its application of filmatic bearing oil were described. The artificial obstacle about native production and hope in future were analysed.

8. 基于变分法提出了一个求解雷诺边界条件下有限长轴承油膜力的快速算法,用此算法对一个三油叶不平衡轴承—转子系统的非线性动力学行为进行了一系列的分析。

Based on the free boundary theory and the variational method, a fast and accurate model for the calculation of the fluid-film forces under the Renolds boundary condition is presented.

9. 当轴旋转的时候就把油溅入轴承。

In rotating, the shaft splashes oil up into the bearings.

10. 输送皂角泵内有设计合理的泄油和回油槽,是齿轮在工作中承受的扭矩力最小,因此轴承负荷小,磨损小,泵效率高。

Pump is the drainage and back into the groove of reasonable design, is a gear in the work under the minimum torque force, so the bearing load is small, wear small, pump with high efficiency.

11. 轴承内侧装设的甩油盘就是借离心作用将可能进入轴承内部的油甩掉,起到密封的作用。

Bearing off the inside of oil pan installed by the centrifugal effect is likely to enter the oil off the internal bearings, seals play a role.

12. 检查轴承是否有油,滑动轴承应检查是否达到规定油位。

Inspect bearing lubrication if the oil level is in normal level.

13. 通过对相对偏心率简化计算误差的分析,提出腔内孔式回油静压轴承设计中的几点建议。

Several Suggestions on designing the hydrostatic bearings by using relative eccentric ratio to simplify the calculating error analysis have been proposed.

14. 轴承座内的油位标记和油位表使油位保持在正确水平。

Oil level marks in the housing and an oil level gauge help to keep the correct oil level.

15. 采用细曲轴及平面滚动轴承技术及较低粘度的冷冻油以提高机械效率。

Applying the slender crankshaft, the level rolling bearing technology, and lower viscosity refrigeration oil, increased the mechanical efficiency.

16. 金刚石轴承具有在空气、油和水中摩擦系数低以及高负载率的特点,与不锈钢轴承相比一些技术方面有待提高。

Diamond bearing with the air, oil and water, low coefficient of friction and high load rate characteristics, compared with some of the technical aspects of stainless steel bearings to be improved.

17. 论述了发动机轴承衬套油线拉制工具的设计及其结构,介绍了油线拉制的方法,并提出了有关注意事项。

The design and structure of the drawing tool for the engine bearing sleeve inside channel is discussed, the drawing technique introduced and the related points put forward.

18. 传感器最佳位置是在曲轴轴承正对的发动机两侧或油底壳处。

The optimal positions of the vibration sensor should be located on both sides of the crank-shaft bearing or bottom of the engine.www.wENtIYi.CoM

19. 对在航空发动机滑油系统断油时的主推力球轴承瞬态热进行了分析。

The transient thermal analysis of the main thrust ball bearing was performed during fuel cut off for an aeroengine oil system.

20. 水轮发电机推力轴承甩油是机组安装、运行中的常见问题,但目前还无法彻底根治。

It is the set installation that the thrust bearing shed oil of hydrogenerator , Common problem in the operation, Yet still can not thoroughly cure once and for all at the moment.

21. 低压系统的滑油供给主轴承和其它轴承。

Lubricating oil of the low pressure system supplies the main and other bearings.

22. 本文介绍了用扁毛细管节流的液体静压轴承的支承面积、扁毛细管尺寸油空压力及轴承刚度等计算。

The article introduces the calculation of bearing area, flat-capillary size, pressure in the Chambers and the rigidity of the hydrostatic bearing throttled by using flat-capillary.

23. 当内圈转动时,应该有回注装置使扔掉的油回注轴承。

With inner-race rotation slingers should be provided to throw the oil back into the bearing.

24. 讨论了在设计参数及运行条件下椭圆轴承和三油楔轴承在中、轻载区的稳定性裕度。

The stability allowance of elliptic bearing and three oil wedge under the design parameter and operating condition in middle and light loading area is discussed.

25. 本研究从固定式三油楔动压滑动轴承动态工作状况分析入手,分析了固定三油楔动压滑动轴承的原理以及变载荷工况下的受力状态;

The thesis come from the analysis of stationary type tri-oil wedge dynamic-pressure sliding bearing dynamic working condition, analyse its elements and stress in variable-load operating mode.

26. 该装置与一油气两相流发生器相连以实现对两相流润油下滑动轴承的气蚀现象的研究。

Connecting with the bubbly oil producing device, this rig can investigate the influence of bubbly oil on the cavitation erosion.

27. 旋涡气泵结构紧凑,体积小,重量轻,不需变速装置,除轴承外其它部位没有直接接触磨擦,噪音低,送出的气源无水无油。

Swirl pump is compact, light weighted and no speed-adjusting device needed, no friction except bearer, low noise, no water and no oil in the output air.

28. 旋涡气泵结构紧凑,体积小,重量轻,不需变速装置,除轴承外其它部位没有直接接触磨擦,噪音低,送出的气源无水无油。

Swirl pump is compact, light weighted and no speed-adjusting device needed, no friction except bearer, low noise, no water and no oil in the output air.

版权声明:问题易所有作品(图文、音视频)均来源网络,版权归原创作者所有,与本站立场无关,如不慎侵犯了你的权益,请联系我们告知,我们将做删除处理!