
词语导航
基本信息
词语:热循环
繁体:熱循環
拼音:rè xún huán
英语翻译
【机】 heat cycle; thermal cycle
相关词条
1.thermocycling 2.thermalcycling 3.thermalcycle 4.heatcycle分词翻译
热的英语翻译:
ardent; caloric; craze; eager; fever; heat; hot; warm【化】 heat
【医】 calor; cauma; febris; fever; fievre; heat; hyperthermia; hyperthermy
phlegmasia; phlegmonosis; pyreto-; pyro-; therm-; thermo-
循环的英语翻译:
cycle; recur; circle; rotate; circulation; repetition; revolution【计】 DO-loop; for-loop; loop; unwinding
【化】 recirculate
【医】 circuIation; cycle
【经】 cycle; revolving; rotation
翻译例句
1. 该热循环仪带有一个程序控制模块。
The thermocycler has a processor-controlled block.
2. 裂纹扩展速率随热循环的进行逐渐减小。
Thecrack propagating rate decreases when the thermal cycles increase.
3. 随着热循环次数增加,垂直裂纹网格变密。wWw.WeNTIYI.coM
The mesh density of vertical cracks increased following thermal cycles.
4. 试验包括热循环、应力循环和应力热循环等。
Experiments carried out include thermal, stress and stress-thermal cyclings.
5. 随热循环上限温度升高,其热疲劳抗力降低。
The thermal fatigue resistance cuts down with the thermal cyclic upper temperature rising.
6. 这些方法是进行一次或多次热循环来产生所需要的结果。
These methods use one or more thermal cycles to produce the desired result.
7. 研究了热循环对铝基复合材料热膨胀和冷却收缩曲线的影响。
The effects of thermal circling on the curve of heat expansion and cold contraction are investigated.
8. 在此基础上采用新回质回热循环方式对机组性能进行了研究。
The adsorption performance is investigated by introducing a novel mass and heat recovery strategy.
9. 热影响区的热循环是决定焊后热影响区组织和性能的重要因素。
Thermal cycling is an important factor to determine structure and property of HAZ after welding.
10. 本文讨论了地层流体的热循环对流对次生孔隙形成和分布的影响。
The discussions are made on the influence of fluid-flowing convection over the formation and distribution of secondary pores.
11. 本文对局部经受高温热循环构件的热弹塑性应力进行了有限元分析。
In this paper, the thermal elastic-plastic stresses of the components which underwent local high temperature cycle were analyzed by FEM.
12. 然而在一次非绝热循环演化过程中,总的相位包括几何相和动力学相。
However the total phase in a nonadiabatic cyclic evolution generally consists of both the geometric and dynamical phases.
13. 结果表明,复合涂层的热疲劳行为与热循环上限温度、涂层厚度有关。
Results show that thermal fatigue behavior is associated with circle temperature and coating thickness.
14. 是否按照文件规定计划进行烤箱热循环测试?是否有客观证据其有执行?
Are thermal profiles performed on the tack dry ovens on a documented schedule? Is there objective evidence that it is being performed?
15. 本文利用空间环境效应地面模拟设备对环氧结构胶粘剂进行了真空热循环试验。
In this paper, using ground-based simulation facilities, the vacuum thermal cycling test was carried out on the epoxy construction adhesive.
16. 利用该模型,根据少量试验数据可预示长期冷热循环下的永久变形或工作寿命。
Using this model the permanent distortion and work life in long term under thermal cycling can be predicted based on a few test data.
17. 结果表明,在热循环过程中基体组织发生动态回复和再结晶,材料产生循环软化;
The results show that the matrix in the microstructure occurs dynamic recovery and recrystallization and the materials generate cyclic softening during thermal cycling.
18. 作为回热循环中的关键部件,回热器性能的好坏对于燃气轮机效率的提高至关重要。
Recuperator, as the key part in recuperated cycle, plays the important role in efficiency increasing of gas turbine.
19. 采用定点激光反射热循环方法,测量了硅基体上铜膜应力随温度的变化及等温松弛。
The stress variation with temperature and isothermal relaxation in copper films deposited onto silicon wafers are studied by fixed point laser reflection method.
20. 通过所建二维细观损伤模型分析了真空热循环次数对材料线膨胀系数曲线影响的原因。
The effect of vacuum thermal cycles on the linear expansion coefficient profile was analyzed using a proposed two-dimensional model of micro-damage.
21. 采用会计模式和矩阵模式热经济学方法对回热循环微型燃气轮机系统进行了分析和研究。
The accounting model and matrix model of thermoeconomics are implemented to study the micro gas turbine with heat recuperator .
22. 通过钨极氩弧焊试验,对焊接热影响区温度场进行分析和研究,建立了焊接热循环曲线。
The temperature field in welding HAZ was studied and analyzed. Welding heat curve was set up by argon-shielded tungsten arc welding experiment.
23. 采用热模拟技术研究了X80管线钢在不同焊接热循环条件下晶粒及第二相粒子的变化。
Thermal simulating technology was adopted to study grain size and the precipitates distribution of CGHAZ for X80 pipeline steel with different welding condition.
24. 结果表明:加工以后使应力重新分布和使残余应力降低或均匀化,冷热循环去应力处理效果很小。
The results indicated that after machining the stress is re arranged and the residual stress decreases; the effect of thermal cycle stress relief treatment is little.
25. 结果表明:加工以后使应力重新分布和使残余应力降低或均匀化,冷热循环去应力处理效果很小。
The results indicated that after machining the stress is re arranged and the residual stress decreases; the effect of thermal cycle stress relief treatment is little.
版权声明:问题易所有作品(图文、音视频)均来源网络,版权归原创作者所有,与本站立场无关,如不慎侵犯了你的权益,请联系我们告知,我们将做删除处理!
