淬火温度用英语怎么说,淬火温度的英文翻译


词语导航

基本信息

词语:淬火温度

繁体:淬火溫度

拼音:cuì huǒ wēn dù

英语翻译

【化】 hardening temperature; quenching temperature

相关词条

1.hardeningtemperature  2.quenchingtemperature  

分词翻译

淬火的英语翻译:

quench
【计】 hardening
【化】 hardening; quench; quenching
【医】 quenching

温度的英语翻译:

temperature
【化】 temperature
【医】 T; temperature

翻译例句

1. 淬火温度越高,焊缝脆化越严重;

The embrittlement of the welds increases with the increase of quenching temperature of PWHT.

2. 结果表明,随二次淬火温度的升高,硬度逐渐升高。

The results show that the higher the second quenching temperature, the higher the hardness.

3. 研究了不同的淬火温度对高硼铸钢冲击耐磨性的影响。

The Influence of quenching temperature on wear resistance of high boron casting steel was investigated.

4. 若淬火温度较高,由于粗大马氏体的存在,脆性很大;

On the other hand, the parts might become more brittle at higher quenching temperature because of the coarse martensite.

5. 结果表明:随着淬火温度升高,材料强度提高,韧性降低;

The results show that with the increase of quench temperature strength rise but toughness is worse;

6. 结果表明:随淬火温度提高,低温回火脆性区向高温区漂移。

The results show with increasing quenching temperature the brittle temperature of the steel tempered at low temperature brittle temperature moves upwards.

7. 结果表明,强度对淬火温度变化不敏感,而低温韧性则较敏感。

The results showed that the strength of the steel is not sensitive to the quenching temperature, but the toughness at low temperature is.

8. 结果表明,在不同淬火温度和保温时间下形成不同的贝氏体形貌。

The result indicates that under different quenching temperature and holding time, the formed bainite morphology are different.

9. 研究了等温淬火温度对ADI中残余奥氏体及其力学性能的影响。

The influences of isothermal quenching temperature on the retained austenite and mechanical properties of ADI were studied.

10. 结果表明,淬火温度、回火温度和运行速度对抗拉强度、屈服强度影响很大。

The results show that the quenching temperature, tempering temperature and speed have great influences on the tensile strength, yield strength.

11. 研究了淬火温度、淬火冷却方式和回火温度对高铬铸铁轧辊组织和性能的影响。

The influences of quenching temperature, cooling pattern and temper temperature on the structures and properties of high chromium cast iron roll were investigated.

12. 本文研究了淬火温度对4330M钢在蒸馏水中的应力腐蚀裂纹扩展速率的影响。

The effect of quenching temperatures on the rate of stress corrosion crack propagation of 4330M steel in distilled water has been investigated.

13. 结果表明,钢球开裂为淬火开裂,淬火温度过高是导致淬火钢球开裂的主要原因。

The main cause of the cracking is that the quenching temperature is too high.Www.Wentiyi.coM

14. 研究了淬火温度和回火温度对ZG310- 510铸钢组织和力学性能的影响。

The Influence of quenching temperature and tempering temperature on mechanical properties and microstructure of ZG310-510 cast steel was studied.

15. 结果表明,随着淬火温度的降低,双相钢的屈服和抗拉强度下降,同时总伸长率提高;

The results showed that the tensile strength and yield strength decrease while total elongation increases with decreasing quenching temperature.

16. 阐述了基于模糊自适应PID控制的钢丝绳用钢丝铅浴淬火温度测控系统的工作原理。

The paper introduced the working principle of the lead hardening temperature measuring and control system for the steel wire base on the fuzzy suitable PID control.

17. 结果表明材料选择错误、淬火温度不当,以及中频淬火区域过小是导致传动轴断裂的原因。

The results indicate that the mistake choice of material, unreasonable quench temperature and too small region of MF quenching are the cause of transmission shaft fracture.

18. 试验结果表明H13钢在最佳完全退火温度、淬火温度、回火温度下可得到最优综合性能。

The test results show that the surface of H13 steel can obtain the optimum performance at temperature of complete annealing, quenching and tempering.

19. 本文据此提出了三维非线性淬火温度场有限元数学模型,模型中耦合了温度和相变潜热的计算。

Accordingly, a nonlinear mathematical model of three dimensional temperature fields in quenching processes has been proposed based on the Finite Element Method in this paper.

20. 研究了在不同等温淬火温度热处理后高硅铸钢的显微组织与残余奥氏体量和材料断裂韧性间的关系。

The influence of austempering treatment on the microstructure, retained austenite and fracture toughness of high silicon cast steel has been studied.

21. 采用感应加热研究X 70控轧钢弯管二次加热力学组织、力学性能随着淬火温度、回火时间的变化规律。

Using the method of induction heating, the regulation of the variety of X70 controlled rolling steel bends"mechanics structure and mechanics property in secondary heating is investigated.

22. 不同的淬火温度使双相钢显微组织中不仅产生了不同体积分数的马氏体,而且也形成了不同数量的新生铁素体。

Different quenching temperatures lead to not only different amounts of martensite, but also different volume fractions of new ferrite.

23. 锰含量提高并选取合适的淬火温度后,残余奥氏体含量及稳定性提高,抗拉强度显著提升的同时保持了较高的伸长率。

The content and stability of retained austenite is higher after more Mn is added, and also the strength is higher with preferable elongation when the appropriate quenching temperature is chose.

24. 用三种碳势、两种淬火方式、三种淬火温度、五种回火温度得出不同含碳量、不同淬火工艺、不同淬火温度的回火曲线。

Three carbon potentials, two quenching methods, three quenching temperatures, five tempering temperatures can finally lead to different tempering curves.

25. 结果表明,奥氏体的再结晶发生在钢的正常淬火温度以上的一个温度范围,并在该范围内存在晶粒细化效果最佳的温度区域;

The results showed that the austenite recrystallization occurs in a temperature range biger than thenormal quenching temperature and there is an optimum temperature range for the grain refining.

26. 结果表明,随着亚温淬火温度的升高,双相组织中马氏体的亚结构由孪晶型变成位错型,两相的变形能力和拉拔性能都得到改善。

Mecrostructure and mechanical properties of 20SiMnTi steel have been studied and analyzed when treated by different heat treatment process, by changing the sub-critical quenching temperatures.

27. 结果表明,各状态试样组织中孪晶的出现,淬火温度、冷却速度的影响是次要的,与合金中的合金元素镍、铬、铜有更密切的关系。

The results show that, the presence of twinning martensite should be attributed to alloying elements addition in steel, and the austenitizing temperature, and cooling rate are not important factors.

28. 但油淬情况就不是如此,因为油淬时在淬火临界阶段零件表面的温度可能仍然很高。

This is not true in oil quenching, when the surface temperature may be high during the critical stages of quenching.

29. 外加磁场淬火的温度场分布模拟是一个新的领域。

The distribution of the temperature field during magnetic field quenching is a kind of new research.

30. 淬火。这个工艺是把材料加热到临界温度范围之上,然后迅速冷却到临界温度范围以下,使钢材明显变硬。

Hardening. This is the process of heating to a temperature above the critical range, and cooling rapidly enough through the critical range to appreciably harden the steel.

版权声明:问题易所有作品(图文、音视频)均来源网络,版权归原创作者所有,与本站立场无关,如不慎侵犯了你的权益,请联系我们告知,我们将做删除处理!