
词语导航
基本信息
词语:焊接状态
繁体:焊接狀態
拼音:hàn jiē zhuàng tài
英语翻译
【机】 as-welded
分词翻译
焊接的英语翻译:
seal; solder; weld
【医】 solder; soldering
状态的英语翻译:
state; condition; fettle; position; predicament; status
【计】 behaviour; S; ST; state; status; transient regime
【医】 asiminine asis; condition; etat; sirupus ferri jodati; state; status
【经】 state
翻译例句
1. 正常焊接状态时变频控制交流脉冲频率。
Varying frequency is used to control AC pulse frequency in normal welding state.
2. 在这种控制法中电流分为焊接状态稳定化脉冲和焊接脉冲。
Electric current is classified into welding state stabilization impulse and welding impulse in this control method.
3. 利用R BF人工神经网络及SVM模型建立电弧声信号与焊接状态的映射模型,从而实现焊接过程状态的模式识别。
RBF Network and SVM model are used to set up the image model of arc sound signal and welding state in order to realize the pattern recognition on-line of the welding conditions.
4. 研究了试件表面处理状态、保护气体、激光输出功率、焊接速度、激光脉冲频率等工艺参数对焊接质量的影响规律。
The influence of the parameters such as surface treatment state, laser output power, welding speed, protective atmosphere, and pulse frequency on the welding quality was studied.
5. 这也从分形理论的角度证明了在超塑性固相焊接头的形成过程中,焊接面各微区的焊合状态是非均匀性的。
It is proved by fractal theory that the welded state of every micro zone at welded surface is uneven in the formation process of isothermal superplastic solid-state welding joint.
6. 利用微机检测焊接电流和时间,运用统计方法获得在不同焊接电流区间的焊接时间,间接给出焊接接头组织性能的状态。
By a method of recording of welding currents and time, the information of joint microstructure and properties can be gained according to the welding time with different currents.
7. 并结合焊接的三种工作状态,分析了逆变电感、负载电阻的变化。WWw.wENTiYI.COM
Incorporating the three working conditions of welding, we analyse the change of inverter inductor and load resistance.
8. 在役管道不停输焊接是在一定的输量、流速、压力的状态下焊接管件,对管道进行维修、改造的一种方法。
In service pipeline non-stop transmission welding is a method to maintenance and rebuild pipeline under welding pipe of certain transmission amount, flow speed, pressure status.
9. 试验证明,采用该技术有助于克服CO2焊接存在的不足,可以更好地实现电弧状态的控制。
It is indicated by experiments that the existing shortcomings of CO2 welding can be overcome, and are states controlled more easily.
10. 电弧焊接过程是一个多因素交互作用的复杂过程,焊接过程的状态与许多参数有关。
Arc welding process is a very complicated process with many interacting factors mixed together, so the transient state of welding process is related to many parameters.
11. 用金属磁记忆检测技术,对不同热处理状态下焊接件的磁场强度进行了检测和分析。
The magnetic density of weldments was detected and analyzed in different heat treatment conditions by metal magnetic memory technology.
12. 激光拼焊技术是将两块或多块具有相同或不同机械性能、不同表面状态的钢板使用激光焊接的方法连接成毛坯件,然后进行整体冲压成轿车结构件。
Tailor welded blanks are defined as two or more sheets of blanks with equal or different mechanical properties, or surface coatings welded together by laser before stamping.
13. 钢材的淬硬倾向、焊接接头含氢量及其分布,以及接头所承受的拘束应力状态是产生焊接冷裂纹的三大主要因素。
Harden tendency of steel, content and distribution of hydrogen in welded joints, restraint stress resistance of joints are three factors that leads to the cold cracks of the welded joints.
14. 探讨了多管程结构以及换热管与管板焊接的焊缝对管板应力状态的影响。
It also probed into the effects of the of multitube pass structure and of the welding seams between heat exchangers and tubesheets on the stress of the tubesheets.
15. 分析了硬质合金微型钻头加工时的受力状态,根据钎焊硬质合金刀具的强度指标要求,研究了刀具焊接强度的检测方法。
The cutting loads of cemented carbide drilling tool in drilling PCB are analyzed, a method applied to testing the brazing strength of cemented carbide cutters is studied.
16. 在橡胶隔膜贮箱的研制中,通过对焊接过程中隔膜受热状态分析,优化选择了电子束焊接规范参数;
In course of the development of the membrane tank, via the status analysis is heated. The electron beam welding norm parameter chose in the optimization.
17. 每次焊接完成后,当加热板处于热状态时,用浸有甲醇的布擦拭加热板表面。
Clean the board surface with fabric soaked with methanol when the board is still hot after each welding is completed.
18. 焊接设备在良好和安全的状态下使用。
All the welding equipments are used under good and safe conditions.
19. 同时研究了焊接工艺参数、热处理状态对接头性能的影响。
The effect of welding parameters and artificial aging on the overlap joints were investigated.
20. 用于呈淬火状态下的低、中合金钢、异种钢结构,以及同类型的热强钢的焊接。
Used for welding in quench low and middle-alloy steel, different type of steel, and same type of high strength steel.
21. 其装置特点是能够轴向直接观察电弧和熔池状态,从而便于控制焊接过程,保证焊缝的对中性。
The main feature of the device is able to observe arc and molten pool directly in coaxial direction so that the welding process is easily controlled and alignment of weld can be warranted.
22. 其装置特点是能够轴向直接观察电弧和熔池状态,从而便于控制焊接过程,保证焊缝的对中性。
The main feature of the device is able to observe arc and molten pool directly in coaxial direction so that the welding process is easily controlled and alignment of weld can be warranted.
版权声明:问题易所有作品(图文、音视频)均来源网络,版权归原创作者所有,与本站立场无关,如不慎侵犯了你的权益,请联系我们告知,我们将做删除处理!
