轴颈用英语怎么说,轴颈的英文翻译


词语导航

基本信息

词语:轴颈

繁体:軸頸

拼音:zhóu jǐng

英语翻译

【化】 journal; shaft neck

相关词条

1.gudgeonjournal  2.journal  3.maneton  4.shaftjournal  5.axleneck  6.axleneck  7.shaftcollar  8.axlejournal  9.pivot  10.trunnion  11.journalofshaft  12.bearinglocation  

分词翻译

轴的英语翻译:

axes; axis; shaft; spindle
【医】 ax-; ax.; axes; axio-; axis; core

颈的英语翻译:

cervical; kink; neck
【医】 cervico-; cervix; colla; collum; der-; dero-; jugulum; neck; trachel-
trachelo-; trachelos

翻译例句

1. 从曲轴颈上拆下活塞和连杆。

Remove piston and connecting rods from crankshaft journals.

2. 轴颈及花键底径的硬化层深度为(0。

When hardened layer depths of axle neck and spline bottom diameter is(0.

3. 在连杆大头安装曲柄轴颈。

The lower end of the connecting rod fits the crankshaft journal.

4. 铁磁性轴颈处在由激发线圈激发的磁场内。

A ferromagnetic shaft journal is suspended in a magnetic field which is excited by surrounding excitation coils.

5. 提出了轴颈倾斜情况下的轴承油膜厚度方程。

The film thickness equation considering the journal misalignment is put forward.

6. 有能力冲洗整个轴颈,保持轴颈和空穴清洁。

Has the ability to purge through the trunnion to keep both the trunnion and the cavity clean.

7. 尾轴承的承载能力随轴颈倾斜率的增大而减小。

The carrying ability of the stern tube bearing decreases with the increase of the inclination of the shaft neck.

8. 这种轴颈向滚子轴承是一种特殊的回转轴承的设计。

The axial-radial roller bearing is a special slewing bearing design.

9. 最后提出了减小曲轴主轴颈径向圆跳动误差的措施。

Finally, the measures to reduce the radial circle run-out error of the crankshaft main journal have be presented.

10. 应用解轮轴颈保护套可以较好地解决“降级”问题。

With the axle journal protection sleeve in disassembling of wheels, the problem of "down grading" can be solved well.

11. 介绍了电厂锅炉引风机承力侧轴颈的磨损和修复情况。

Abrasion and repair condition of axle neck of induced draft fan for boiler in power plant is introduced.wWW.weNTIYI.cOm

12. 本文简述了一种正在兴起的曲轴连杆轴颈的磨削方法和原理。

The article introduced a grinding method and principle of the journal of crankshaft connecting rod.

13. 采用基于激光熔覆的方法实现了大磨损量的风机轴颈的修复。

The repair of ventilator axle journal with serious wear was achieved by using the method of laser cladding.

14. 类似的打磨烧蚀还会造成襟翼滑架轴颈断裂。 (图10和11)。

Similar grinding burns also have led to the fracture of flap carriage spindle journals (figs. 10 and 11).

15. 连杆的一端与曲轴的连杆轴颈相连,另一端通过活塞销与活塞相连。

The connecting rod is attached at one end to a crankpin on the crankshaft and at the other end to a piston, through a piston pin or wrist pin.

16. 本文阐述了水轮机导叶轴颈J型密封的结构、工作原理及其合理性。

In this paper, the construction, principle and reasonableness of J seal of turbine guide vane trunnion are presented.

17. 在发动机里,机油被供应到旋转在其支承轴内的曲轴和凸轮轴轴颈上。

In the engine, oil is supplied to crankshaft and camshaft journals rotating in their supporting bearings.

18. 连杆的作用是将活塞承受的压力传给连杆轴颈。同时,连杆做偏心运动。

The connecting rod carries the power thrusts from the piston to the crankpin. At the same time, the rod is in eccentric motion.

19. 该方案实现了轴颈的自动定位和测量,减小了人工测量误差,实用性较强。

With this scheme, the automatic positioning and measurement of the axle journal is realized, the manual measurement error is reduced, and the scheme is fairly practical.

20. 针对多辊筒碾压机压辊轴颈磨损严重的问题,对其进行了故障分析和改造。

Aimed at the wear problem of roll axle neck, failure analysis and rebuilding were made for multi-roller mill.

21. 曲轴的各轴颈在很高的比压下作高速旋转运动,使轴颈和轴承受到强烈磨擦。

Because the shaft necks whirligig with high speed under high pressure, the shaft necks and bearings endure intense attrition.

22. 常见的电动机轴颈磨损原因:装配不合理、键装配不合理、电动机轴承损坏。

The usual reasons of abrasion of electric motor crankshaft are in the following: unreasonable assembly, unreasonable key assembly as well as the spoilage of electric motor bearings.

23. 最后,在组装过程中,当部件通过键槽时,注意避免损坏密封和轴的轴颈表面。

Lastly during assembly care is taken to avoid damaging the seals when passing over the keyway or performing bearing surfaces of the shaft.

24. 本文对具有高承载能力的空气静压轴颈轴承进行了研究,给出了实验和计算结果。

This paper has investigated air hydrostatic bearings with high load carrying capacity and given experimental and calculating results.

25. 同样,在进行曲轴轴颈和曲轴轴承配合间隙的测量时,也可以借鉴这种操作技巧。

Similarly, in the crankshaft journal and crankshaft bearing clearance measurements, they can draw on such skills.

26. 当有径向载荷作用时, 自主式轴承能抑制轴颈位移并因此使轴承获得无穷刚度。

When radial load is applied, the active bearing can surpress the displacement of the shaft, thus obtaining an infinite stiffness.

27. 万向节十字轴的四个轴颈叫做万向节十字头,分别装在两个万向节叉顶端的轴承中。

The four arms of the spider, known AS trunnions, are ASsembled into bearings in the ends of the two shaft yokes.

28. 在分析运动规律和损坏状况的基础上,提出把十字轴轴颈加工成锥度的办法减轻轴颈损坏。

On the bases of analysis for motion regularity and damage condition, a method for taper machining of cross shaft journal is proposed to reduce journal damage.

29. 在分析运动规律和损坏状况的基础上,提出把十字轴轴颈加工成锥度的办法减轻轴颈损坏。

On the bases of analysis for motion regularity and damage condition, a method for taper machining of cross shaft journal is proposed to reduce journal damage.

版权声明:问题易所有作品(图文、音视频)均来源网络,版权归原创作者所有,与本站立场无关,如不慎侵犯了你的权益,请联系我们告知,我们将做删除处理!