
词语导航
基本信息
词语:高速轴
繁体:高速軸
拼音:gāo sù zhóu
英语翻译
【化】 high speed shaft
分词翻译
高速的英语翻译:
high speed
【机】 top speed
轴的英语翻译:
axes; axis; shaft; spindle
【医】 ax-; ax.; axes; axio-; axis; core
翻译例句
1. 研究了火箭发动机高速旋转试验台高速轴在工作激振频率内的振型。
The mode shapes of the high-speed shaft in rotating test-bed for rocket engine within working excited frequencies were studied.
2. 某电厂发生锅炉磨煤机变速箱高速轴断裂,双列调心滚子轴承损坏。
The high speed shaft of the coal mill gear box for the boiler in a power plant broke, and the double-row self-aligning roller bearing was damaged.
3. 针对生产中增速箱的高速轴振动频繁现象,对其齿轮强度进行了校核。
According to the frequent oscillation of high-speed axle of speed increasing box, the gear strength is checked.
4. 带整体齿轮的高速轴和带套筒轴承的平衡惰轮轴确保降低机组震动并延长密封寿命。
High speed shaft with integral gear and balanced idler shaft with sleeved bearings to insure a low vibration unit and extended seal life.
5. 本文针对高速离心泵高速轴轴承经常烧瓦事故进行了详细的分析并给出了改正措施。
In this article, the failure of burning shaft tile occurred frequently in tangent pumps was analyzed and the protection method for this accident was presented.
6. 还阐明了弹性联轴器的阻尼,刚度和高速轴上各转动惯量等参数对起升机构动力响应的影响。
Moreover, the article elucidates the influence of various parameters on the dynamic response of the hoist - the damp of elastic coupling, stiffness, each turning inertia of hoist shaft, etc.
7. 现有风力机制动装置的制动闸安装在高速轴,制动力矩不可调,其主要缺陷有:制动安全性能差;
The existing wind braking device"s brake is installed in the high-speed shaft, thus braking torque is not adjustable, and the main defects are:the braking safety performance is poor;
8. 详细分析了引起膨胀机齿轮箱高速轴振值高的原因,提出了解决问题的办法及日常运行中应注意的问题。
Cause of high vibrated value of turbo-expander gearbox high-speed shaft was analysed in this paper. solution and attention problems were put forward.
9. 建立了含有虚约束的多相并列平行曲柄机构受力分析模型。在此基础上分析计算了三环减速器的轴承载荷和高速轴曲柄上的转矩;
The load of planetary bearings and the moment in the high speed shafts are analyzed and some suggestions about the structure type and design parameters of the three ring reductor were a…
10. 高速大长径比压力反应釜搅拌轴密封性能问题一直是设计者与使用者研究的难题。
The sealing property problem for the stirring shaft of high-speed pressured reaction axe with large length to diameter ratio is always a difficult problem to study for designers and users.
11. 利用磁流体密封原理可解决因轴高速旋转摆动带来的密封困难问题。
On the basis of the principle of magnetic fluid seals the paper has resolved the handicap of seals arising from the wiggle of high speed shaft.
12. 两轴式卷线器的刹车具有两个主要目标、1规定线杯的最高速度低于路亚出线的速度,2控制速率的衰减,防止炒粉。
Brakes of casting reels has two major objectives, 1 to set the maximum spool speed and the lure speed just after line released, and 2 to control the decelerate rate to prevent birds nest.
13. 高速大长径比搅拌轴密封可靠性问题,一直是从事密封工作者探索的问题之一。
The question about the seals of high speed churn shaft with large ratio of length to diameter is one of the difficult problems.
14. 文章介绍了万向轴驱动装置在高速列车和电动车组上的应用。
The applications of the cardan shaft driving device in high speed electrical locomotives and EMUs are described.
15. 提出了对驱动轴按函数规律直接控制的方法,以保证并联机床手控运动的高速高精度。
A direct control method based on actuators" length function was presented, which may ensure high precision and high speed of hand control mation of parallel machine tools.
16. 通常情况下,气井井轴周围的高速流动为非达西流动,产生附加压降。WWw.WenTIYI.com
Generally, flow at high velocity around well bore in gas well is belong to non-Darcian flow which arising adding pressure drop.
17. 收、卷采用无轴气动锥顶装置,单独电机驱动,双工位收放料,不停机高速自动接料功能,提高了工作效率。
Reeling is equipped with shaft - less pneumatic cone top device, individual motor drive, double work - place, non - stop high speed automatic picking function, which upgrades the working efficiency.
18. Z轴采用表面阳极化航空铝合金,温度一致性极佳;并降低了运动部件的质量,减少测量机在高速运行时的惯性。
Cross beam and Axis Z are made of surface-anodized aerometal to improve thermal stability and reduce moving mass for faster setting.
19. 介绍了一种检测高速线材轧机轧辊锥轴与锥套锥度的检测方法以及相应的锥体锥度检测仪。
A kind of measuring method and corresponding measuring instrument for measuring cone shaft and cone sleeve of the high-speed wire rolling mill"s roller are introduced.
20. 对Y500 -2型高速柔性轴电机进行了全面的振动测试。
This paper introduces the whole vibration test process of Y500 2 type high speed flexible shaft motor.
21. 建立了DMU-70V五轴数控高速加工中心主轴-夹具-刀具系统的有限元模型,并利用动态测试的方法对有限元计算结果进行验证;
The FEM(finite element method) of the main shaftclamping apparatus-cutter system for DMU-70V NC high speed machining was built, and the results of the FEM were validated using dynamic test.
22. 提出将单轴振动电机横置于筛体上作为高速振动筛的振动源。
A monoaxial vibrating motor placed transversely on a sifter as a vibration source of a high speed sifter was developed in this paper.
23. 圆轴体同圆盘形孔体的联结,越来越多地采用过盈配合,传递扭转力矩,高速地旋转。
Cylinder shaft body is connected to its hole body more and more by pinch fit so as to transmit torsional moment at high speed of revolution.
24. 对涡轴发动机动力涡轮转子测扭基准轴的不平衡量进行了研究,提出了一种通过高速动平衡试验估算出测扭基准轴不平衡量的试验方法。
The torque tube unbalance of turboshaft power turbine rotor is investigated and a test method for estimating the unbalance is introduced with high speed dynamic balance test.
25. 重型不锈钢轴:高速运转时刚性强,不易损坏,坚实耐用。
Heavy stainless steel shaft: when high-speed running rigidity is strong, uneasy to damage, solid and durable.
26. 轴与叶轮采用特殊一体式加工,保证叶轮在高速下的平衡运转。
Axis impeller machining using the special one, to ensure the balance of the impeller at high speed operation.
27. 本文分析了汽车传动轴高速状态下横向振动的稳定性与扭转振动,以及摩擦力、阻尼和花键轴的运动对横向振动的影响。
The stability of transverse vibration in high speed automobile and the influence of torsional vibration, friction, damping and movement of spline shaft on vibration are discussed.
28. 结果表明:测扭基准轴的不平衡量虽然不是转子高速动平衡的决定性因素,但影响到传动轴的动平衡。
The results have shown that the torque tube unbalance is not a key factor in high speed dynamic balance, but effects the power shaft.
29. 该高速动车组的双联式虎克万向节传动轴,均匀传递转矩和旋转运动。
The dual units type Hookes cardan shaft of EMUS can transfer equably torque and rotating motion.
30. 该高速动车组的双联式虎克万向节传动轴,均匀传递转矩和旋转运动。
The dual units type Hookes cardan shaft of EMUS can transfer equably torque and rotating motion.
版权声明:问题易所有作品(图文、音视频)均来源网络,版权归原创作者所有,与本站立场无关,如不慎侵犯了你的权益,请联系我们告知,我们将做删除处理!
