淬火应力用英语怎么说,淬火应力的英文翻译


词语导航

基本信息

词语:淬火应力

繁体:淬火應力

拼音:cuì huǒ yīng lì

英语翻译

【机】 quenching stress

分词翻译

淬火的英语翻译:

quench
【计】 hardening
【化】 hardening; quench; quenching
【医】 quenching

应力的英语翻译:

stress
【化】 stress
【医】 stress

翻译例句

1. 对2 0钢渗碳后的淬火应力与畸变进行了有限元计算。

The quenching stress and distortion of carburized 20 steel are calculated by finite element.

2. 研究结果有助于复杂薄壁壳体淬火工艺制订及淬火应力和畸变规律的认识。

The study results are helpful to designing of quenching process and understanding of quenching stress and distortion regularity for complex thin shell.

3. 轧制应力对淬火应力影响很小,淬火应力却彻底改变了原有轧制应力的大小和分布。

The influence of rolling stress towards quenching stress is little, but quenching stress totally changes the original rolling stress.

4. 位错的形成与离子注入引进的损伤和淬火过程中的热应力有关。wWW.WeNTiYi.COM

The ion-implantation damage defects and thermal stress during quenching step are responsible for the formation of dislocations.

5. 时效处理:指让产品通过低温通风炉以释放淬火造成的应力的工艺。

AGING: the process of running product through low temperature air draw furnaces for the purpose of relieving stress which was caused in the hardening operation.

6. 淬火裂纹:裂纹在钢材的淬火或淬火后形成,由于冷却时的高应力所造成;也有可能是在淬火油中的水所导致。

Quench Cracks: Cracks formed in a steel part during or after quench, resulting from high stresses in cooling; could be caused by water in the quench oil.

7. 轴承零件在淬火冷却过程中因内应力所形成的裂纹称淬火裂纹。

Bearing parts in the process of hardening cooling by internal stress due to the formation of quenching cracks crack said.

8. 结果表明:由于焊接电流过大,使焊缝产生淬火马氏体组织及较大的焊接残余应力,导致镀锌氢脆敏感性增加,造成吸油盘发生氢脆开裂。

The large welding current caused the formation of quenched martensite and the high residual stresses in the welding zone, resulting in the increase of zinc sensitivity of hydrogen attack.

9. 通过对淬火试件进行金相组织分析和残余应力测量,验证了数值模拟的可行性。

Through the microstructure analysis and residual stress measurement on a quenching test-piece, the feasibility of the numerical simulation is proved.

10. 在实验室条件下研究了冷拔与水淬火工艺对予应力钢丝力学性能的影响。

Effects of cold drawing and water quench process on mechanical properties of prestressed wires have been studied in laboratory.

11. 本文研究了淬火温度对4330M钢在蒸馏水中的应力腐蚀裂纹扩展速率的影响。

The effect of quenching temperatures on the rate of stress corrosion crack propagation of 4330M steel in distilled water has been investigated.

12. 在淬火过程数值模拟基础上,进一步提出了回火过程的数值计算模型,其中着重考虑了应力松弛现象。

On the basis of the numerical simulation of quenching process, this paper further gives a numerical calculation model of tempering process, emphatically take the stress relaxation into account.

13. 采用非线性等参元三维有限元算法(FEM)成功地模拟了形状复杂的零件淬火过程中瞬态温度场、相变、应力和应变,获得直观的立体图象。

Three dimensional nonlinear and isoparameter FEM has been successfully used to simulate the transient temperature field, phase transformation, stress and strain of complex components during quenching.

14. 此外,还定性分析了淬火、回火后残余应力的性质及热处理工艺过程对裂纹形成的影响。

In additions the paper qualitatively analyses the influence of residual stresses occurring after quenching and tempering and the process of heat treatment on the formation of the cracks.

15. 实践证明,采用高温淬火和中间消应力退火可显著提高其使用寿命。

Experimental results showed that the service life of die can be improved evidently by using high temperature quenching and stress relief annealing.

16. 结果表明,尖角效应引起的应力集中和热处理淬火加热温度偏高是导轨端面产生裂纹的主要原因。

The results show the stress concentration caused by acute angle effect and the high temperature are the primary cause of producing crack.

17. 淬火过程中的快速冷却在工件内部产生的内应力是导致淬火变形的根本原因。

The stress produced by quick cooling inside workpiece during quenching treatment is the main reason of quenching deformation.

18. 论述了感应淬火零件的残余应力形态,并对载货车半轴的材料、硬化层深度及法兰圆角淬火层分布提出了个人见解。

This paper demonstrates residual stress of induction quench parts and personal views about stress distribution of flange corner heat treatment, truck half axle material and depth of hardened layer.

19. 固溶、淬火等热处理手段极大地提高了其机械强度,但同时使其内部产生了较大的残余应力。

Heat treatment methods, such as solid solution and quenching, have greatly enhanced its mechanical strength, which also leave a large internal residual stress in it.

20. 结果表明,高温淬火和分级淬火可使应力腐蚀断裂抚力k _ (ISCC)值得到明显提高。

Results show that both high temperature quenching and step quenching can apparently increase the stress corrosion cracking resistance K_ (ISCC).

21. 淬火过程是典型的温度-组织转变-应力耦合的过程,准确模拟淬火过程十分困难。

For quenching processes are typical temperature - phase transformation - stress coupled processes, it is quite difficult to precisely predict the processes.

22. 因此,研究淬火残余应力的形成及影响因素是极为重要的。

Therefore, the study of the formation of quenching residual stress and impact factors is extremely important.

23. 利用高碳钢淬火试样及淬火后充氢试样的拉伸试验,研究了高碳钢淬硬组织对氢和应力的敏感性。

The sensibility of the harden structure of high carbon steel to hydrogen and stress is researched through the tensile test of quenched specimens and charging hydrogen specimens after quenching.

24. 经试验分析是由于该段晶粒粗大,淬火时组织应力超过该段的材料强度所致。

Through test analysis, we found that it is caused by the large size grain in this section, as well as the structure stress in this section over the material strength.

25. 航空铝合金为了获得高强韧性,必须进行固溶与时效处理,在淬火过程中产生很大的淬火残余应力。

These precipitation-hardened aluminum alloys gain their high strengths through heat treatment involving a severe quenching operation, which introduces a very high level of residual stresses.

26. 激光淬火硬化层应力状态为压应力。

The stress state of laser hardened case was press stress.

27. 认为,淬火过程中产生的局部拉应力加上尖锐V型槽口引起的应力集中是造成开裂的主要原因。

It is concluded that the local tensile stress created during quenching process and the stress concentration due to sharp V-shaped notch are the primary reasons of cracking.

28. 研究表明碳素钢予应力钢丝采用水淬火取代铅浴进行索氏体化处理是可行的。

Effects of cold drawing and water quench process on mechanical properties of prestressed wires have been studied in laboratory.

29. 介绍了渗碳淬火零件热处理畸变的原因,分析了热处理内应力的形成过程。

The present paper analyzed the reasons of heat treatment distortion of carburizing and hardening components and the formation process of the internal stress.

30. 介绍了渗碳淬火零件热处理畸变的原因,分析了热处理内应力的形成过程。

The present paper analyzed the reasons of heat treatment distortion of carburizing and hardening components and the formation process of the internal stress.

版权声明:问题易所有作品(图文、音视频)均来源网络,版权归原创作者所有,与本站立场无关,如不慎侵犯了你的权益,请联系我们告知,我们将做删除处理!