弧电压用英语怎么说,弧电压的英文翻译


词语导航

基本信息

词语:弧电压

繁体:弧電壓

拼音:hú diàn yā

英语翻译

【电】 arc voltage

分词翻译

弧的英语翻译:

arc
【化】 arc
【医】 arc

电压的英语翻译:

tension; voltage
【化】 voltage
【医】 electric tension; voltage

翻译例句

1. 起弧电压对字迹模糊度影响不大。

The arc voltage has little effect on ambiguity of words.

2. 研究了气压和起弧电压对喷号机喷字效果的影响。

The effect of pressure and arcs voltage on marked effect of spray marking machine was studied.

3. 在埋弧焊接的变速送丝系统中,其电弧电压的稳定是依靠调节送丝速度实现的。

The stability of arc voltage is realized by adjustment of wire feeding speed in constant wire feeding system of SAW.

4. 以氮气滑动弧为例,分析了其在一个周期内电弧电压、电流、电阻和功率的变化特性。

The arc voltage, current, power and resistance of a nitrogen gliding arc in one period were studied.

5. 现代下降特性电子弧焊电源设置的后拖特性一般是由电弧电压取样作为参考电压形成的。

The electron arc welding power source without sampling of arc voltage is introduced in this paper.

6. 设有收弧功能,粗焊丝焊接后,松开枪头微动开关,送丝与电弧电压自动衰减填满弧坑。

It has ending arc function, after the welding of thick welding wire, loosing sensitive switch, the voltage of arc and welding torch.

7. 主要研究A105钢小直径焊丝埋弧焊时,电弧电压、焊接电流和焊接热输入对焊缝成形的影响。

The effects of arc voltage, welding current and heat input on the weld appearance in submerged-arc welding(SAW) of A105 steel with small diameter welding wire were experimentally researched.

8. 对本质安全电感电路,最小建电弧电压能反映电路的建弧特性,电流变化率能反映电路的电感特性。

For an inductive intrinsically safe circuit, minimum arcing voltage shows the arcing characteristics and current reducing rate shows the inductive characteristics.

9. 研究了所制备薄膜的厚度、颗粒度等与薄膜制备过程中激光脉冲频率、引弧电压和靶材—衬底间距等工作参数之间的对应关系。

We studied the relationship between the films thickness, grain size and deposition parameters, i. e. pulse laser frequency, striking voltage and distance from the target to the substrate.

10. 根据电离气体中性化条件,初步探讨了在低气压下空心阴极电弧放电的引弧过程,分析了影响低气压下空心阴极电弧放电引弧电压的因。

Aslo the paper has dealed with the mechanism of the hollow cathode vacuum arc discharge and analyzed the starting arc process according to the neutralizing theory of ionized gas.

11. 单片机对焊接电流、电弧电压、电流给定、脉冲周期、占空比、基值电流、收弧电流衰减时间、前气和后气时间等焊接参数进行采样、计算和控制。

The welding current, arc voltage, preset current, the period and ratio of pulse, base current, down slope time, gas pre and post flow time are sampled, calculated and controlled by microprocessor.

12. 在火花试验装置上进行爆炸试验,得到本质安全复合电路的放电波形,发现电弧电压基本维持在最小建弧电压,而电容电流随着电路参数的不同而发生振荡。

It was found that when the capacitive ignition occurred, arc voltage will keep minimum arcing voltage, but arc current possibly attenuates in sinusoidal form with different circuit parameters.

13. 但氩气等离子弧的电压较低,焓值不高,切割能力有限,与空气切割相比其切割的厚度大约会降低25%。

But the argon plasma arc voltage, low enthalpy is not high, cutting ability is limited, and cut the air than the thickness of the cut about 25% lower.

14. 试验研究了不同微弧氧化电压和脉冲频率对涂层微观形貌,涂层厚度及相组成的影响。

The effects of different oxidation voltage and pulsed frequency on microstructure, thickness and phase constitute of the coatings have been investigated.

15. 文章介绍了装置的设计思想和部件设计原理,对产品的安全载流、电压损失、滑接性能、灭弧性能进行了分析。

This article describes the design principle of the device and its parts, analyses the safe current-carrying capacity, voltage drop, sliding contact and are extinction performances of the device.

16. 文中采用无源探针对由等离子弧梯度电压和等离子鞘层电压构成的等离子反翘(等离子云)电压进行检测。

A non power supply probe was developed to detect the plasma cloud voltage, which consists of plasma arc voltage gradient and plasma sheath voltage.

17. 利用X射线对气体分子的电离作用,在一定电压下用一束X射线照射真空灭弧室,使灭弧室内产生电离电流。

The remainder molecules in the vacuum tube will be ionized by X-ray irradiation, the ionization current can be detected at a constant DC voltage.

18. 不过CO_2焊射滴过渡只能发生在潜弧状态下,产生潜弧的条件为在CO_2气氛中,使用粗焊丝,大电流和低电压的配合参数。

The condition inbwhich the arc is buried are that the parameters such as CO_2 gas, thick wire, high current and low voltage should be used.

19. 在焊接电流确定的条件下,引弧瞬间的焊机输出电压反映了焊接电缆长度、截面积以及地线连接情况等重要信息。

When welding current is fixed, some important information such as length and section area of welding cable, connection of ground wire can be shown by output voltage of instantaneous arc-striking.

20. 通过此方法计算在大气过电压情况下的弧垂曲线,能满足工程需要。

The sag curve at atmospheric over-voltage calculated by this method can meet the needs of engineering.

21. 本文以动态绝缘为设计目标,提出高电压真空灭弧室的全程优化设计方法。

Aim at the higher level of dynamic insulation design, a whole optimized design method for high voltage vacuum interrupters is proposed.

22. 介绍提高我国弧焊逆变电源可靠性的途径以及零电压、零电流软开关变换研究现状。

Ways to improve the reliability of arc welding inverter power and the research condition of zero voltage, zero current soft switch inverter are introduced.

23. 介绍开断近区故障(SLF)时恢复电压的计算和灭弧室在不同燃弧时间下的理论分析。

Introduction to calculation of recovery voltage in short line fault (SLF) and theoretical analysis of the interrupter in various arcing time.

24. 以工业级硅酸钠为电解液,铝材在交流电压作用下进行等离子微弧氧化反应,电压升高,膜厚增大。

Using commercial sodium silicate as electrolyte, aluminum surface was treated with plasma micro-arc oxidation under alternate current, film thickness increased with the increase of voltage.

25. 为了进行电源系统分析和设计,本文建立了电压模式和峰值电流模式控制的逆变弧焊电源数学模型,并用计算机进行分析。

In order analyze and design the power supply system, the system models which control by two above-mentioned control modes are established and analyzed by computer.

26. 介绍了三相五柱式消弧线圈的工作原理,单相电弧接地过电压的工频熄弧理论。

The principle of arc-suppression coil with three phases and five columns , and theory of power frequency extinguishing arcing were introduced.

27. 在弧焊逆变电源中采用LD C滤波电路,可以降低直流线上的电压纹波。

The LDC filter is introduced into a rc welding inverter power source and the voltage ripple of the DC line is decreased.

28. 在弧焊逆变电源中采用LD C滤波电路,可以降低直流线上的电压纹波。Www.wenTIyI.COM

The LDC filter is introduced into a rc welding inverter power source and the voltage ripple of the DC line is decreased.

版权声明:问题易所有作品(图文、音视频)均来源网络,版权归原创作者所有,与本站立场无关,如不慎侵犯了你的权益,请联系我们告知,我们将做删除处理!