喷油用英语怎么说，喷油的英文翻译

词语导航

基本信息

词语：喷油

繁体：噴油

拼音：pēn yóuwww.wentiYi.COM

英语翻译

【化】 oil blooming

相关词条

1.fueloilinjection  2.oilthrow  3.oilblowout  4.oilinjection  

分词翻译

喷的英语翻译：

gush; spew; spout; spray; sprinkle; spurt

油的英语翻译：

paint; fat; grease; oil
【化】 oil
【医】 elaeo-; eleo-; oil; Ol; olea; oleo-; oleum

翻译例句

1. 油箱在大量喷油。

The tanker was gushing oil.

2. 不用喷油，我想做个花样然后吹干。

Don"t use a hair spray. I want my hair set and dried.

3. 这口油井每天喷油500吨。

The oil well delivers 500 tons a day.

4. 用黄油涂一下锅底，或者用不粘锅的喷油。

Oil the griddle with butter, or spray it with non-stick cooking spray.

5. 该方法可实现对喷油规律的不解体检测。

The method can realize nondestructive testing for fuel injection law without disassemble.

6. 将面团压入已喷油的9个3英寸的弹簧脱底烤模。

Firmly press mixture into bottom of a 9 x 3-inch springform pan coated with cooking spray.

7. 我们力求避免那种陈旧的，富有浪漫色彩的喷油方式。

We endeavour to avoid the old, romantic idea of a gusher.

8. 通过控制共轨压力和控制脉宽可实现灵活的喷油规律。

The flexible injection characteristics can be acquired by controlling common rail pressure and pulse width coordinately.

9. 讨论调整喷油始点对控制直喷式柴油机排放性能的影响。

Finally, the effects on the emission control of di diesel engine are discussed.

10. 试验结果表明在30度左右喷油提前角时综合油耗最低。

The experimental results showed that about 30 degrees of injection angle gave the lowest consumption of fuel.

11. 密立根用一个香水瓶的喷头向一个透明的小盒子里喷油滴。

Using a perfume atomizer, he sprayed tiny drops of oil into a transparent chamber.

12. 针对柴油机电控喷油系统磁电式执行器的控制问题进行了研究。

In this paper, the control problem of electromagnetic actuator in electronically controlled diesel fuel injection system is investigated.

13. 在改进喷油器结构的基础上，在中压共轨喷油系统中实现了预喷。

The pilot injection is realized in medium pressure common rail electronic diesel injection system on the basis of injector structure modification.

14. 高压共轨式电控喷油系统是一种综合性能比较好的柴油机喷油系统。

The high-pressure common rail electronically controlled fuel injection system is a kind of the well-performance diesel injection system in general.

15. 由于篇幅的限制，本文仅介绍NIRVANA喷油螺杆空压机的特点。

Owing to space constraints, this paper introduced only NIRVANA injection screw air compressor characteristic.

16. 喷油压力、喷油始点、喷油持续角和喷油率均取决于柴油机转速和负荷。

The injection pressure, timing, duration and rate depend on the engine speed and load.

17. 文中利用该装置研究了轴针式喷嘴的喷油过程，探讨了喷嘴油束形成的特征。

The apparatus has been used in investigating the spray formation of a pintle nozzle.

18. 现代高速电子喷油柴油机在拖轮和工作船推进主机的应用中，体现出很多优点。

Modern high speed electronic injection diesel engine has many advantages when used onboard tugs and workboats for propulsion.

19. 最后，在分析上述测量结果的基础上，建立了一种判别喷油开启压力大小的方法。

Finally, on the basis of analysing above-mentioned measured results, a method of distinguishing nozzle opening pressure change is set up.

20. SS法为可控喷油形成准均质稀混合气的优化控制策略开辟了一条新的技术途径。

SS set up a new technique approach which gives a new controlled strategy for optimizing the formation quasi-homogenous mixture.

21. 结果表明：遗传算法可适用于多设计变量、多设计目标的柴油机喷油系统参数优化设计。

The process of the parameter optimization design based on GA was introduced and briefly discussed in many of its respects.

22. 试验结果表明：所建立的模型可以用来定量地分析各种结构和控制参数对喷油过程的影响。

Test results show that the model could be used to analyzing the effects of injecting process that were caused by all kinds of parameters.

23. NIRVANA喷油螺杆空压机同普通喷油螺杆空压机相比，驱动部分的结构被大大简化。

NIRVANA injection screw air compressor with ordinary injection screw air compressor driven part of the structure, compared to be greatly simplified.

24. 在高速柴油发动机喷油系统性能检测中，一般以燃油压力信号作为喷油系统性能检测参量。

The fuel pressure signal was considered as the performance testing parameter of the spray system in high speed diesel engine performance testing.

25. 本次审核发现，工厂喷油部门和移印部门至少60名使用化学品的工人没有做过职业病体检。

It was noted that at least 60 employees in paint spraying department and tempo-printing department have not ever conducted occupational health examination since they had joined the facility.

26. 如对喷油系统油压信号的采集，即需要具有高速采集数据的性能，又要能满足特殊同步的要求。

For example, the characteristics of data acquisition system for sample oil pressure signal of an injection system are of high speed, and special synchronization.

27. 计算结果表明，选择合适的压缩比、喷油提前角，可以改善缸内的燃烧过程，降低燃油消耗率。

The calculation result indicates that choose the appropriate compression ratio, the Angle of fuel injection can improve the cylinder burn and reduce the fuel exhaust.

28. 公司目前拥有CNC数控机床、EDM火花机、铣床、注塑机、喷油无尘车间等各种先进生产设备。

At present the Company holds CNC numerical control machine tool, EDM spark machine, milling machine, injection machine, and oil injection non-dust workshop and other advanced manufacture equipments.

29. 公司目前拥有CNC数控机床、EDM火花机、铣床、注塑机、喷油无尘车间等各种先进生产设备。

At present the Company holds CNC numerical control machine tool, EDM spark machine, milling machine, injection machine, and oil injection non-dust workshop and other advanced manufacture equipments.