极限孔用英语怎么说,极限孔的英文翻译


词语导航

基本信息

词语:极限孔

繁体:極限孔

拼音:jí xiàn kǒng

英语翻译

【机】 limiting orifice

分词翻译

极限的英语翻译:

limit; terminal; the maximum; utmost
【化】 limit(ing) point

孔的英语翻译:

aperture; bore; foramen; hole; os; ostium; vulva
【化】 hole; opening
【医】 apertura; aperturae; aperture; bore; coel-; foramen; foramina; hiatus
mesh; opening; pore; Pori; porosity; porus; trema

翻译例句

1. 利用极限分析原理对土体中泥浆护壁深钻孔的极限孔深问题进行计算研究。

The limit deepness of deep bore-hole with mud dado in the soils is calculated and analysed by adopting theory of limit analysis.

2. 如果减振器的振幅变大,控制活塞会移动到它的极限位置然后会终止旁通孔的油路,从而开始提供完全的阻尼力。

If the excitation of the shock absorber is greater, the control piston moves to its limit position so that oil ceases flowing through the bypass duct, meaning that the full damping force is available.

3. 分析了剪胀和软化程度对球孔扩张时的应力、位移、塑性区半径及极限扩张压力等方面的影响,并将大、小应变理论的结果进行了比较。

The influence of softening extent on stress, displacement and the radius of plastic zone during expansion as well as the extreme expansion pressure are studied.

4. 在塑性极限分析的基础上,本文提出受内压球壳开孔接管的一种整体补强设计方法。www.WENTiyi.cOM

This paper describes a design procedure of spherical shells with nozzles subjected to internal pressure based onthe limit analysis.

5. 分析结果表明,拉深孔排列规律、密度和孔径变化对板料的极限拉深高度有很大影响。

The results indicated the arrayed rule, density and diameter of the drawing holes affect the limit drawing height of sheet metal drastically.

6. 法兰螺栓口中心圆的直径的容许偏差及法兰相邻两孔极限容许偏差的应小于0.6毫米。

Permissible deviation of bolt hole circle diameter on flange and permissible limited deviation of two adjacent holes on flange shall be less than 0.6mm.

7. 本文通过3组9个抗压试件,了解开槽砌块灌孔砌体的受压开裂荷载、极限承载力、破坏形态和变形能力。

In this paper, 9 compressive specimens of 3 groups were tested to investigate the cracking resistant load, ultimate load, failure modes and deformation capacity of the grouted slotted block masonry.

8. 通过分析深小锥孔开式冷挤压成形特点 ,描述了其成形极限 ,建立了变形区非稳态连续速度场 ;利用上限原理得到了成形极限的理论模型。

The experiments to explore the rheologic properties of semisolid continuous casting billets of A356 alloy in the semisolid state have been carried out by means of the multifunctional rheometer.

9. 通过分析深小锥孔开式冷挤压成形特点 ,描述了其成形极限 ,建立了变形区非稳态连续速度场 ;利用上限原理得到了成形极限的理论模型。

The experiments to explore the rheologic properties of semisolid continuous casting billets of A356 alloy in the semisolid state have been carried out by means of the multifunctional rheometer.

版权声明:问题易所有作品(图文、音视频)均来源网络,版权归原创作者所有,与本站立场无关,如不慎侵犯了你的权益,请联系我们告知,我们将做删除处理!