
词语导航
基本信息
词语:内接头
繁体:內接頭
拼音:nèi jiē tóu
英语翻译
【化】 inner joint
分词翻译
内的英语翻译:
inner; inside; within
【医】 end-; endo-; ento-; in-; intra-
接头的英语翻译:
connect; get in touch with; joint; piece
【计】 splice
【化】 adapter
翻译例句
1. 本衬垫适用于角钢对接内接头CO2单面焊使用,有各种规格供选用。
This backing(internal) is specially designed for CO2 one-side welding of angle steel butt joints. Different backing sizes are supplied.wWw.WenTiyI.cOm
2. 本发明公开了一种密封内接头,所述一种密封内接头包括一个有槽管件内接头和二个密封圈。
The present invention discloses a sealing union, which comprises a union of pipe fittings with groove and two sealing rings.
3. 开发的新型管道封堵器由中心管、气囊、活塞、弹簧、夹板、护板、内接头、外接头、连接板和楔键等组成。
A newly developed pipeline plug is composed of a central pipe, balloon, piston, spring, clamp, backplate, inside and outside joints, connecting plate and a wedge key.
4. 除非电源接头是防火花的,否则不要再30米距离内,为电器设备通电。
Do not connect electrical equipment to a power source less than 30 meters away, unless the power source has spark-proof connectors.
5. 正在流动的垫圈材料还会限制气体流程和堵塞在接头螺纹内。
The flowing washer material can also restrict flow paths and jam in the connection threads.
6. 现在这个接头能够从罐子和内胆内推上来。
This fitting can now be pushed up inside the tank and bladder.
7. 将主阀盖上的配管接头螺丝松开,释放阀内压力。
The main valve fittings with screw lid release, pressure release valve.
8. 在相同结构和装药量的条件下,复合射孔在井下作业能够产生较高的枪内压力,容易引起接头的剪切脱落失效。
Under the conditions of similar structure charging rate, higher pressure in the perforators can be produced in downhole operation by using combined perforation, failure would be caused in its joints.
9. 物料通过出料接头内的单向阀门,进入出料软管,进入待灌空瓶,完成一次灌装。
The material enters the discharge hose through the one-way valve in the outlet joint. Now a filling cycle is completed.
10. 它是个上端为钻杆母扣或者由壬,下端为套管公扣,内空心的转换接头。
Its upper end is drill pipe box or union, the nether end is casing pin. It is a crossover with hollow inside.
11. 采用弹塑性有限元方法,建立了套管接头磨损拉伸与抗内压的有限元力学模型。
By using the elastoplastic finite element method, mechanical model for wear tension and internal pressure resistance of casing joints is set up.
12. 使用一个柔性接头将测井管串与爬行器段隔开,以实现连续工具串在井内的定位和居中。
The logging string was decoupled from the tractor section using a flex joint to enable consistent tool positioning and centralization in the well.
13. 根据“球面上圆构造椭圆锥面”的原理,设计了球内接三通接头。
According to the principle of constructing elliptical conical surface by the circles on a sphere, a T-joint inscribed in a sphere is designed.
14. 接头抗剪强度表明,在一定范围内,采用复合钎料可以明显提高接头强度。
Shear results of joints show that joint strength can be increased obviously in a certain range with composite soldering materials.
15. 棱 增加物的塑造在自动制冷管的范围内、接头螺栓的座套表面。
Addition of chamfering shape on seating surface of joint bolt at atf cooler pipe area.
16. 当岩心筒在井下被卡住时,很容易地从安全接头螺纹处倒开,起出内筒和岩心,只留下外筒进行打捞。
When coring barrel gets stuck downhole, it is very easy to back off safety joint to trip out inner barrel and cores, and only left outer barrel for fishing operation.
17. 据此,从结构和内压角度,应用塑性动力学的数值方法和材料的破坏判据分析了引起接头脱落失效的几种因素。
On the basis stated above, a numerical method of plastic dynamics and material failure judgment are used to analyze the causes of joint failure from the aspects of structure and internal pressure.
18. 聚四氟乙烯组件是由经特殊工艺处理的聚四氟乙烯内管,不锈钢丝增强曾外套和两端金属接头组成。
The teflon hose module is by passes through special craft processing the teflon inner tube, the stainless steel wire enhancement level coat and the both sides metal attachment compose.
19. 法兰,管接头,以及阀门不包括在其它特别引用的ASTM规定范围内。
Flanges, unions, and valves not included in the scope of other ASTM specifications are specifically referenced.
20. 结果表明:在役焊接接头残余应力分布规律与常规焊接保持一致,符合管道焊接接头“内凸外凹”的变形机理,但在数值上差别较大。
Results show that distribution regularity of residual stress of in-service keeps coherent with routine welding, which measures up deformation mechanism of welding, but numeric value is different.
21. 用内孔焊结构代替传统的端面焊结构是提高换热器管子与管板焊接接头抗应力腐蚀和缝隙腐蚀稳定性的根本途径。
Substituting inner-hole welding construction for traditional end surface welding construction is a fundamental method for raising the stabilities of anti-stress corrosion and anti-slit corrosion.
22. 该法对电缆绝缘接头处VHF和UHF信号的时域和频域分析可有效地识别被测电缆绝缘接头部内、外部的局放信号。
This method analyzes VHF and UHF signal of detected cable joint, using time and frequency analysis. This method can be used for detecting PD pulse inside or outside the insulating joint.
23. 去除焊缝余高或将焊缝设计在最大剪应力平面内可明显改善对焊接头的疲劳性能。
The fatigue resistance of the butt welds can be improved by means of removing the weld reinforcement and designing the weld in the maximum shear stress plane.
24. 肿瘤坏死因子受体相关因子是细胞胞浆内的一类重要的接头分子。
Tumor necrosis factor receptor-associated factor family is an important binding protein group in cytoplasm.
25. 本试验首次采用再结晶显示金属内塑性变形区的方法观察分析了焊接接头中冷裂纹产生的塑性变形区域。
In this investigation recrystallization in metals was first used to study the plastically - deformed zone induced by cold cracking in welds.
26. 焊接接头的耐点蚀性能明显下降,点蚀优先发生在高温热影响区所在的铁素体晶粒内。
Consequently, pitting corrosion resistance of the welded joint declines obviously and pitting preferentially occurs at ferrite phase in the high temperature HAZ near the fusion line.
27. 绝缘接头与管线连接后,不许在接头5米内起吊管线。
It is forbidden to lift pipe within 5 meters closed to the joint after insulation joint is connected to the pipe.
28. 管件类:弯头、三通、四通、活接头、卜芯、大小头、管帽、堵头、内丝、外丝、翻边、异径管。
Pipe series: Elbow, tee, cross, movable joint, Bu core, reducer, pipe cap, choke plug, inside the wire, outside the wire, turned-over edge, increaser etc.
29. 外钳打在上边的接头上,内钳打在下边的接头上。
The make-up tong is placed on the top tool joint and the break-out tong is placed on the bottom tool joint.
30. 外钳打在上边的接头上,内钳打在下边的接头上。
The make-up tong is placed on the top tool joint and the break-out tong is placed on the bottom tool joint.
版权声明:问题易所有作品(图文、音视频)均来源网络,版权归原创作者所有,与本站立场无关,如不慎侵犯了你的权益,请联系我们告知,我们将做删除处理!
