塑性屈服用英语怎么说,塑性屈服的英文翻译


词语导航

基本信息

词语:塑性屈服

繁体:塑性屈服

拼音:sù xìng qū fú

英语翻译

【化】 plastic yielding

分词翻译

塑的英语翻译:

model; mold

屈服的英语翻译:

give in; bend; bow; knuckle under; submit; succumb; yield
【化】 yield; yielding

翻译例句

1. 用广义应力表达了框架柱的塑性屈服条件。

The plastic yield condition of frame column is rep - resented in stress resultants.

2. 断口主要分为塑性屈服变形区和弹性变形区两部分。

Fracture surface consists of plastic yield deformation area and elastic deformation area.

3. 提出了一种新的损伤塑性本构模型,强调了应力三轴比对塑性屈服的影响。

A plastic constitutive damage model was proposed with special concerns being put on simulating the stress triaxiality-dependent hardening phenomena.

4. 通过对塑性屈服单元进行参数优化,较真实地模拟了地下洞室开挖后围岩塑性圈的影响。

Through optimization of plastic yield element parameter, The influence of adjoining rock plastic circle is simulated true.

5. 这种柔性界面层促使尼龙6基体局部区域塑性屈服被认为是高岭土增韧尼龙6的主要机理。

Partial matrix yielding caused by this kind of flexible interlayer is the main mechanism of kaolin toughened nylon 6.

6. 通过烧结铁圆柱试样单向压缩试验,验证了粉末冶金烧结材料广义塑性屈服条件的合理性和适用性。

Based on the single axial compression of sintered iron cylinder specimens, the rationality and applicability of generalized yield criterion are validated for sintered powder metallurgy materials.

7. 通过烧结铁圆柱试样单向压缩试验,验证了粉末冶金烧结材料广义塑性屈服条件的合理性和适用性。

Based on the single axial compression of sintered iron cylinder specimens, the rationality and applicability of gene...

8. 结构钢材的韧性随温度降低而下降,其破坏形态也由塑性屈服向脆性断裂转变,构件的承载力也由强度控制变为材料的韧性控制。

The toughness of steel decreases as temperature drops, its breakage transfers from plasticity to brittleness and the loading capacity is controlled by the toughness, not the strength.

9. 此时,系统达到临界平衡状态时所对应的材料强度降低倍数即为整体最小安全系数,临界平衡状态定义为边坡内的塑性屈服区能够形成潜在的滑移通道时的状态。

The minimum safety coefficient was defined as the reduction coefficient, when the system was fairly close to the limit equilibrium state through decrement of material strength step by step.

10. 所研究的水泥浆配方体系具有:可流动时间长、沉降轻微、塑性粘度和屈服值小及凝固后具有较高的抗压强度等特性。

The formulation system is of the characteristics of long mobile time, light settling, small plastic viscosity and yield value, higher compression strength etc.

11. 土体总的变形由三部分组成:即弹性应变、与体积屈服机制相关的塑性应变和与剪切屈服机制相关的塑性应变。

The total deformation of soils consists of three parts: elastic strain, plastic strain related to volumetric yielding mechanism and plastic strain related to shear yielding mechanism.

12. 复合材料的塑性理论通常包括三方面准则:屈服准则、流动准则和强化准则。

The plastic theory of composite material include three criterions: the yield criterion, the flow rule and the hardening rule.

13. 在经典弹-塑性理论的屈服函数中引入应变梯度及考虑应变率效应的函数。

The second shear strain gradient and the function reflecting the effect of strain rate are introduced into the yield function of classical elastoplastic theory.

14. 结果显示:改性浇铸尼龙材料拉伸屈服后能够产生很大的塑性形变,不会发生脆性破坏。

The results showed that cast nylon modified with laurolactam could produce heavy plasticity deformation without brittle destruction after the tensile yielding.

15. 实验中通过采用LF 2和LY 12两种铝合金筒坯,获得金属材料的塑性和屈服强度对旋压件可旋性影响的一般规律。

During experiments, aluminum alloy LF2 and LY12 are used in order to obtain the influence of plasticity and yield strength of metal materials on spinnability of spun parts.

16. 用比拟的方法分析和计算了爆炸焊接条件下,爆炸复合材料结合区中塑性变形金属的动态屈服强度值。

This paper analysed and calculated the dynamic yielding strength of plastic deformed metal in the bonding zone of explosive welding composite material in the condition of explosive welding.

17. 它是材料屈服、弱化或塑性变化的必然结果。

It is an inevitable result due to material yield, weakening or plastic variation.

18. 本文介绍了确定具有塑性予应变板材后继屈服条件的实验方法。wWw.wEnTiyI.cOM

The experimental method for determine the subsequent yield condition of a sheet with plastic prestrain is introduced.

19. 该涂料为带有屈服值的假塑性流体。

The paint is fake plastic fluid with a yield value.

20. 文章为高压传压介质叶蜡石选择了一个塑性本构模型,它包括DP屈服准则和相关联的流动准则。

The plastic constitutive model which involves DP yielding principle and relevant flowing principle was selected for high pressure conduction medium pyrophyllite.

21. 热疲劳抗力主要取决于材料的高温屈服强度,在强度、塑性及循环热稳定性取得适当配合时最大。

The thermal fatigue resistance mainly depends on the high temperature yield strength and will become maximum, if the strength, plasticity and cycle thermal stability are in an adequate combination.

22. 通过测定不同新拌水泥浆体的剪切应力、屈服应力、塑性粘度等流变参数,绘制流变曲线,分析含不同高效减水剂的新拌水泥浆体的触变性。

Mapping rheogram and analyzing thixotropy of fresh cement paste with different superplasticizers by measuring the rheologic parameters such as shearing stress, yield stress and plastic viscosity.

23. 经过验证,塑性势函数等于屈服函数,流动规律为相适应的流动法则。

It has been verified that plastic potential function is equal to yield function and flow law is the associated flow rule.

24. 粉末冶金材料屈服条件是广义塑性理论的重要基础。

The yield criterion for powder metallurgical materials was a key basis of generalized plasticity theory.

25. 塑性变形常用屈服函数描述,损伤变形则可以引入一种类似的损伤函数加以描述。

Usually yield function is introduced to describe the plastic deformation, however, a new damage function is proposed here to describe the additional deformation due to the damage of soil structure.

26. 研究了变形速度,试验温度以及预先塑性变形程度对氢致表观屈服强度下降的影响。

The effect of loading rate, test temperature and pre-plastic deformation on hydrogen induced apparent yield stress reduction have been investigated.

27. 研究了变形速度,试验温度以及预先塑性变形程度对氢致表观屈服强度下降的影响。

The effect of loading rate, test temperature and pre-plastic deformation on hydrogen induced apparent yield stress reduction have been investigated.

版权声明:问题易所有作品(图文、音视频)均来源网络,版权归原创作者所有,与本站立场无关,如不慎侵犯了你的权益,请联系我们告知,我们将做删除处理!