词语导航
基本信息
词语：搭接接头
繁体：搭接接頭
拼音：dā jiē jiē tóu
英语翻译
【化】 lap joint
相关词条
1.lapbutt 2.lapjoint分词翻译
接的英语翻译：
receive; accept【电】 connecting
接头的英语翻译：
connect; get in touch with; joint; piece【计】 splice
【化】 adapter
翻译例句
1. 试验结果表明，铝和镀锌钢能得到成形良好的搭接接头。
The results indicate that good lap joint between aluminum and galvanized steel sheet can be made in appropriate parameters.
2. 研究了间隙长度和间隙位置对不同单搭接接头强度的影响。WwW.wentiYI.cOm
The influence of length and position of recessing on the strength of adhesively bonded joints with different single-lap length was presented.
3. 利用有限元方法研究了金属镶嵌对单搭接接头应力分布的影响。
The finite element method (FEM) is applied to investigate the effect of metal inlay in single lap joint on the stress distribution.
4. 研究单搭接接头胶缝中预留间隙对接头拉剪强度和应力分布的影响。
The effect of the recessing on the strength and stress distribution of adhesively bonded single-lap joints is discussed.
5. 焊接和有关技术。电阻点焊凸焊或缝焊搭接接头。带解释的缺陷分类。
Welding and allied processes. resistance spot, projection and seam welded lap joints. classification of defects with explanatory comments.
6. 搭接接头的塑性较差，伸长率仅有3.18%，不及母材伸长率的25%；
The elongation of joints was only 3.18%, less than 25% that of base metal.
7. 用三维弹塑性有限元分析方法，全面分析了点焊搭接接头的应力分布情况。
Using method of three dimensional FEM analysis, whole stress distribution in the joints is are obtained.
8. 运用固有应变法研究了六个固有应变分量分别对搭接接头焊接角变形的影响。
The effect of each inherent strain component on the angular distortion of the lap joint is studied using inherent strain method.
9. 以搭接接头形式为例，采用最坏情况法分析了装配顺序对最终装配偏差的影响。
Taking the form of lap joint as an example, the effect of final assembling deviation affect by the assembly sequence was analyzed by adopting the method of worse condition.
10. 依据受力与变形理论较为精确地给出了搭接接头侧面角焊缝中的剪应力分布规律。
According to the theory of bearing forces and deformations this paper gives distribution laws of the shearing stresses in the side fille welds of overlap connection with comparative accuracy.
11. 依据受力与变形理论，较为精确地给出了搭接接头侧面角焊缝中的剪应力分布规律。
According to the theory of bearing forces and deformations, this paper gives distribution laws of the shearing stresses in the side fille welds of overlap connection with comparative accuracy.
12. 设计中还采用了多种形式的相贯节点，包括圆管正偏心的间隙接头及方管的搭接接头。
Varied types of intersecting joints, including gap joint with positive eccentricity for the circular tubes and overlap joint for the square tubes, were also adopted in the design.
13. 研究了不同搭接接头形式，胶粘剂毛边和拉伸剪切强度的测试方法对拉伸剪切强度的影响。
The effects different joint forms, queer out and the measuring ways on tensile sheer strength are studied in the paper.
14. 介绍了大电机紫铜带线圈斜搭接接头电阻钎焊装置工作原理、参数选择以及钎焊质量的控制。
The resistance brazing principle; the selection of brazing parameters and quality control measures are introduced for the lap joints of copper strip rotor coils within big electrical generator.
15. 运用弹塑性有限元法，研究了胶粘剂弹性模量对含间隙的铝合金单搭接接头上应力分布的影响。
The effect of elastic modulus of adhesive on the str ess distribution in aluminium alloy single lap joint was investigated using elastic-plastic finite element method(FEM).
16. 对双搭接接头进行了边界元应力分析，并和有限元结果进行了对比，从而证实本文方法的有效性。
The BEM technique for adhesive-bonded structure proves valid by comparing the stress distribution for double lap joint calculated in this paper with that calculated by finite element method.
17. 运用弹塑性有限元法结合实验研究了连续和间隙连接的单搭接接头应力分布规律，并考虑了胶瘤的影响。
The stress distribution of continuous and recessed bonding single-lap joints is discussed with use of elastoplastic finite element method (FEM) and experiment, considering the effect of fillet.
18. 基于对实际点焊接头硬度分布的分析，建立了包括熔核、热影响区和母材的单点点焊搭接接头计算模型。
Based on the hardness analyses of actual spot welded joints, a computational model that consists of nugget, HAZ and base metal is established for the single point spot welded lap joints.
19. 结果表明，当焊接工艺参数合适时，可以获得表面成形良好、无变形的铝合金与钢的对接接头和搭接接头。
The results shown that a deformation-free joint with good weld surface appearance can be obtained with suitable welding conditions for butt-joint and lap-joint of the dissimilar materials.
20. 通过SEM、EPMA、EDS、显微硬度计和拉伸实验机对搭接接头的微观组织及力学性能进行了研究。
Microstructure characteristics and mechanical properties of lap joints were researched by SEM, EPMA, EDS, micro-hardness tester and tensile experiment machine.
21. 研究了在胶瘤中嵌入三角形金属楔块对单搭接接头强度和应力分布的影响，结果表明，金属楔块能显著提高接头的强度。
The influence of embedded trilateral cross-section metal bar in the fillet on the strength and stress distribution of single lap joints was discussed.
22. 这些元素可以以不同方式组合在一起，例如：一个搭接接头可能用角接、塞焊和缝焊固定，一个丁字接头可以用一个搭接或槽焊来完成。
The elements can be put together in various ways. For example, a lap join may be held by a fillet, plug, or slot weld, and and a tee joint by a fillet or groove weld.
23. 试验结果表明，配筋多孔砖墙与配筋普通砖墙具有相近的抗震性能，水平筋采用搭接接头时不能发挥钢筋的抗剪作用以及端部锚固钢筋具有提高承载力和约束砌体作用等。
The test results show that the reinforced porous brick wall similar tO normal reinforced brick wall on aseismic design, shear resistance of the bar cannot be used very much when using lap joint...
24. 正在讨论的波音737-300型飞机只用了15年。当其外壳沿敲平的上端搭接接头剥落开来时，飞机上的118位乘客正飞行在34000英尺（刚刚超过10,000米）的上空。
The Boeing 737-300 in question was only 15 years old when its skin peeled open along a riveted lap-joint while flying above 34,000 feet (just over 10,000 metres) with 118 passengers on board.
25. 正在讨论的波音737- 300型飞机只用了15年。当其外壳沿敲平的上端搭接接头剥落开来时，飞机上的118位乘客正飞行在34000英尺(刚刚超过10,000米)的上空。
The Boeing 737-300 in question was only 15 years old when its skin peeled open along a riveted lap-joint while flying above 34, 000 feet (just over 10, 000 metres) with 118 passengers on board.
26. 半导体激光器发出的激光经过柱透镜形成一出射光片。它与母材成一定角度投射到接头上，光片与搭接接头会成一单光纹，而母材垂直上方的CCD摄像机拍摄折线光纹，同步送计算机处理。
The light-plate that is shot by semiconductor laser comes to a certain Angle to throw overlap joint, which brings a single vein of light, and CCD camcorder shoots and sends it to the computer.
27. 在有限元方法的基础上，利用变密度法对单搭接胶接接头搭接区域的被粘物形状进行了拓扑优化，通过曲线拟合得到了较为合理的轮廓。
Based on finite element method, variable density method was employed to optimize the configuration of adherends in overlap region, and the curve fitting was applied to attain proper configuration.
28. 通过优化搭接焊形式能提高焊接接头的最大剪切力。
The maximum shear strength of welded joints can be increased by optimizing the form of lap welding.
29. 通过优化搭接焊形式能提高焊接接头的最大剪切力。
The maximum shear strength of welded joints can be increased by optimizing the form of lap welding.
版权声明：问题易所有作品（图文、音视频）均来源网络，版权归原创作者所有，与本站立场无关，如不慎侵犯了你的权益，请联系我们告知，我们将做删除处理！