
词语导航
基本信息
词语:设备法兰
繁体:設備法蘭
拼音:shè bèi fǎ lán
英语翻译
【化】 girth flange; vessel flange
分词翻译
设备的英语翻译:
equipment; facility; fixing; fixture; installation【计】 device; implementor
【化】 equipment
【医】 equipment; unit
【经】 equipment; facility; installation
法兰的英语翻译:
flange【化】 flanch; flange
翻译例句
1. 本文叙述了设备法兰的优化设计过程和结果,并通过应力测试试验,证明该设计基本可靠。
The course and results of optimized design of shell flanges are described. Through stress measurements made this design proved reliable on the whole.
2. 介绍真空设备法兰采用大直径O形环橡胶自紧式密封(不用螺栓和螺母)的设计计算及其应用效果。WWW.wENtiyI.COM
The design calculation of the large O ring rubber self energized seal (without bolt and nut )used for the vacuum equipment and its application results are introduced.
3. 分析了不同载荷对塔设备法兰受力的影响,指出计算承受外载的法兰强度应根据不同的载荷选取不同的方法。
The influence of different loads on the stress of flange of tower is analyzed. It is thought that the different methods on the intensity calculation should be chosen according to the different loads.
4. 传感器采用贴面形式安装在物体表面,固定形式为螺纹或法兰,并确保与设备表面接触严密。
The sensor shall be mounted on object surface, by fixation of screw thread or flange, and ensure firm contact with the equipment surface.
5. 弯头应该用螺栓固定在湿井地面,并且设计成具有不需要任何螺栓、螺母或皮带即可连接泵设备的连接法兰的能力。
The elbow shall be bolted to the floor of the wet-well and be so designed as to receive the pump connecting flange without the need for any bolts, nuts or clamps.
6. 设备口法兰的类型、等级及端面应符合买方图纸或数据表的规定。
The type, rating and facing of nozzle flanges shall conform to those specified in Purchaser"s drawing or data sheet.
7. 如指定使用外螺纹及内螺纹或榫面及槽面法兰,容器设备口法兰端面应为凹槽型。
When male and female (M&F) or tongue and groove (T&G) type flanges are specified, the nozzle flange facing of the vessel shall be of female or groove type.
8. 铁路运输设备。标准轨距铁路车辆的法兰互联装置的连接。尺寸、连接测量和公差。
Railway transport equipment. Connection for flange intercommunication for standard-gauge line stock. Size and fastening-measurements and tolerances.
9. 某些系统配置,包括旋启式止回阀直接连接到其他法兰设备的场合可能要求考虑这种螺栓所需要的间隔。
Certain system configurations involving direct connection of a Swing Check Valve to other flanged equipment may require consideration of this bolt clearance.
10. 分析比较了在不同锻压设备上进行重型法兰叉类件锻造成形的特点,对其模具进行了优化设计和失效分析。
Forging forming of heavy flange and fork by different forging equipment has been analysed with die optimization and failure analysis for the purpose of higher productivity and lower die cost.
11. 螺栓法兰连接是石油化工设备和管道中应用最为广泛的密封形式。
Bolted flanged connections are the most commonly used in petrochemical equipment and piping system.
12. 锻造生产各种机械、车辆、机电设备等零部件毛坯和成品,及链轮、齿轮、发动机零部件、法兰等产品。
Forging production of machinery, vehicles, electrical and mechanical equipment, spare parts rough and finished, and sprocket, gear, engine components, flanges and other products.
13. 该系列产品适用于不同温度、压力范围内的水蒸气、空气及油类等介质为主的设备、管道法兰连接所用的密封衬垫材料。
It is used as the sealing on equipments, pipes, flanges contacting with the media such as water, air and oil at different temperature and pressure.
14. 所有设备口法兰及翼缘法兰螺栓应为双头螺栓。
All nozzle flange and girth flange bolts shall be of stud bolt type.
15. 从而可实现采用小吨位设备,制造出加工余量少的变截面带双法兰钢半球壳锻件。
This new method made it true to use light tonnage equipment to forge the half spherical steel shell with small metal allowance and variable sections.
16. 组合带法兰部件(如压力控制设备)的过程。
The process of assembling flanged components such as pressure-control equipment.
17. 是制作角铁法兰、型材滚圆弯曲的理想设备。
It"s ideal equipment for bend Angle iron flange.
18. 设备配备无菌空气呼吸器,CIP清洗喷头、视镜、法兰式快开人孔等装置。
The machine equips with asepsis respirator, CIP cleaning spray tip, sight glass, and flange quick open manhole.
19. 为便于安装,制造商设计了一个环形螺栓安装面,以使与其它设备的法兰安装相配合,这使得筒形法兰的制造更容易。
For ease of installation, the manufacturer designs a circular bolts, to install the equipment installation of flange with other match, which makes the cylindrical flange manufacture more easily.
20. 然而,在小曲率半径井中,ESP设备的法兰连接面要承受巨大的弯曲应力,设备受损几率增加,ESP系统的稳定性降低。
However, in these tight-radius wellbores the bolted flanges connecting ESP system components are subjected to extra stress, resulting in potential equipment damage.
21. 设计了能在高辐射环境下工作的、全自动检查核电站反应堆压力壳连接处法兰面主螺栓孔螺纹表面缺陷的设备,解决了自动小车的设备承载和准确定位问题。
To inspect the defects on the screw hole surfaces of nuclear reactor pressure vessel in nuclear power station, an automatic moving table was designed to carry sophisticated inspecting devices.
22. 该设备生产效率高,加工精度高,确保了同尺寸法兰之间的互换性。
Ensure high efficiency and accuracy. So could ensure interchange within the same size flange.
23. 安装搅拌器的设备口的法兰面同容器轴线的垂直度容许偏差为1/500。
The flange face of agitator mount nozzle shall be perpendicular to vessel axis within tolerance of 1/500.
24. 该设备适用于水箱内胆上的加热器法兰及进出水管、热管接头的自动化焊接。
The machine is applicable for automatic welding for heater flange, inlet and outlet pipe and heat pipe.
25. 压力容器设备中法兰与筒体、法兰与接管连接处的C类焊缝和封头端部、筒体上马鞍形的D类焊缝是最为不规则的且施焊工艺最为复杂的焊缝。
In pressure vessels, C and D seam which are located at the joint of flange, tube-shape object, jointed tube, and head of pressure vessels separately are the most complex seams.
26. 压力容器设备中法兰与筒体、法兰与接管连接处的C类焊缝和封头端部、筒体上马鞍形的D类焊缝是最为不规则的且施焊工艺最为复杂的焊缝。
In pressure vessels, C and D seam which are located at the joint of flange, tube-shape object, jointed tube, and head of pressure vessels separately are the most complex seams.
版权声明:问题易所有作品(图文、音视频)均来源网络,版权归原创作者所有,与本站立场无关,如不慎侵犯了你的权益,请联系我们告知,我们将做删除处理!
