受力面积用英语怎么说，受力面积的英文翻译

词语导航

基本信息

词语：受力面积

繁体：受力面積

拼音：shòu lì miàn jī

英语翻译

【机】 area of thrust surface

分词翻译

受的英语翻译：

accept; bear; endure; recieve; stand; suffer

力的英语翻译：Www.wEnTiyi.Com

all one"s best; force; power; puissance; strength
【化】 force
【医】 dynamo-; ergo-; force; potency; potentia; Power; stheno-; strength; vis

面积的英语翻译：

acreage; area; proportion
【计】 A

翻译例句

1. 设备基础的受力面积可根据当地的地质条件相应变化，但必须挖至老土层。

According to the local geology condition, basis force area can change, but must dig to old soil layer.

2. 如有必要，可将支点下放置一块垫板，以增加受力面积，将负载分散到地面。

If necessary, provide a wider base by putting the fulcrum on a board that will spread the load on the ground.

3. 结果表明：花样游泳运动员身材匀称，水中受力面积大，体脂百分比大，趋向“4—1—4体型”。

Results show that the swimmers are of proportional build, bigger body floating area, larger body fat percentage, and their bodily form types approach "4-1-4 bodily form type" .

4. 使用该透镜测厚仪时，透镜的受力面积较大，从而可避免透镜局部受力产生形变而造成的测量误差。

When in use of the lens thickness gauge, the force bearing area of the lens is greater, thereby avoiding the measurement errors caused by the deformation due to the local force bearing of the lens.

5. 考虑到碳纤维水泥试件很难直接感应到车辆的荷载，提出了改变受力面积来增大碳纤维水泥试件所受压力的特殊构件。

It is hard for CFRC to directly sense the load of vehicles, and the special component which can enhance the stress by changing the pressed area.

6. 它应该等于压强，或者说是单位面积上的受力。

It should be a pressure which is a force per unit area.

7. 换句话说，这就是单位面积上的受力。

In other words, it"s force per unit area.

8. 当韧性材料被测试时，由于颈缩使横载截面面积减小，以至在受力没有增加的情况下引起应力的增加，以保证延伸继续如常进行。

When a ductile material is tested, the reduction in cross-sectional area due to waisting causes an increased stress without an increased force, to ensure that extension proceeds uniformly.

9. 自动靴面定型机可视鞋面面积大小调整所需行程深度，依材质特性调整需承受力、下料速度、定型时间、定型温度、下刀顶料压力，使鞋面定型翘度更加完美。

Automatic upper moulding machine can adjust depth according to upper proportion. Change pressure, speed, time, temperature, etc according tomaterial. The upper can get best effect.

10. 试验模拟了切削面积、接触弧长、切削面形状、切削齿后倾角和岩石性能对PDC切削齿破岩受力的影响。

The effects of cutting area, contact arc length, the geometry of cutting face, back dip angle of PDC cutter and rock performance on force of PDC cutter breaking rock were simulated experimentally.

11. 假如，帐篷是平顶的，那么受力就是一个大气压(约10的5次方帕)乘面积！

If, tent is flat-roofed, so getting power is an atmosphere (5 of about 10 square handkerchief) take an area!

12. 最后，给出了基于面积匹配约束的受力点寻址三维算法，主要是用于解决一些扁平状软组织受力时的受力点处理不足。

Finally, an area matching based force point searching method is applied to solve the force point location problems caused by flat-form model.

13. 并且，由于增加了焊接结合面积并有效转移了薄弱受力面，使导丝连接安全性得到提高。

Moreover, due to increasing the welding combination area and effectively transferring a weak stress surface, the connection safety of the guide wire is increased.

14. 通过有限元程序对点支式玻璃幕墙索桁架支承体系中索桁架结构高度、拉杆截面积、拉杆预拉力和玻璃面板厚度对其受力性能的影响进行了研究。

The main parameters considered are height of the cable truss, area of cross section of tensile bar, pre-tension of tensile bar and thickness of glass panel.

15. 对某航炮用气推弹在膛口流场中的受力进行了工程估算，并计算了该弹的脱壳运动情况，分析了气孔面积对脱壳时间的影响。

It estimates the forces acting on APDS in the muzzle field and calculates the movement of sabot and rod. It also analyzes the effect of gas hole area on the time of sabot discarding.

16. 利用真空输纸特性，建立输纸带透过面积的数学模型和纸张受力的分析模型。

According to the vacuum feeding feature, the mathematical model for suction area of the Suction-Tape feeding Table and the analysis model of forcing on paper are set up.

17. 重点研究在条形荷载作用下承压面积比及偏心距等因素对高强混凝土试件局部承压受力性能的影响。

The paper is focused on the study of the influence of the factors such as the bearing area ratio and its eccentricity act on the local bearing strength of the high strength concrete.

18. 单位长度上分布钢筋的截面面积不宜小于单位宽度上受力钢筋截面面积的35％；

The cross sectional area of the distributing concrete every unit length should be not suitable less than 35% of the ratio of reinforcement;

19. 单位长度上分布钢筋的截面面积不宜小于单位宽度上受力钢筋截面面积的35％；

The cross sectional area of the distributing concrete every unit length should be not suitable less than 35% of the ratio of reinforcement;