铁液用英语怎么说，铁液的英文翻译

词语导航

基本信息

词语：铁液

繁体：鐵液

拼音：tiě yè

英语翻译

【机】 melted iron

分词翻译

铁的英语翻译：

determine; iron; unalterable; weapon
【医】 Fe; ferri; ferrum; iron; mars; sidero-
【经】 iron

液的英语翻译：

fluid; liquid; succus
【化】 liquor
【医】 Fl.; fld.; Fluid; humor; juice; Liq.; sap; succi; succus

翻译例句

1. 气孔是由铁液内部的气体形成的。

The blowhole is formed from the gas inside the iron melt.

2. 其中碳饱和铁液作阳极，渣中的银液作阴极。

Thereinto, the carbon saturated iron melt was used as anode and liquid silver as cathode.

3. 介绍高炉铁液采用喂镁包芯线脱硫的试验情况。

The investigation on desulphurization of liquid pig iron by injecting Mg-containing cored wires was introduced.

4. 本发明公开了降低球墨铸铁铁液中含钛量的方法。

The invention discloses a method for reducing the titanium content in ductile iron liquid iron.

5. 本文采用有限元法建立了铁液包倾转力矩数学模型。

The mathematical model of the molten iron ladle was established using finite element method.

6. 铁液包倾转力矩是铁液包结构设计中一个重要问题。

The torque of the molten iron ladle is a very important problem when designing the structure of molten iron ladle.

7. 铁液含有过量的氧、氢、氮都能促使铸件产生气孔缺陷。

Molten iron containing excessive oxygen, hydrogen and nitrogen would promote the blowhole to form.

8. 用数值模拟方法研究了工艺因素对硅铁在铁液中熔化过程的影响。

The effects of technical factors on melting process of ferrosilicon in liquid iron are studied by using numerical simulation.

9. 在炼钢、炼铁过程中，钢水、铁液温度是其中最重要的参数之一。

During smelting steel and iron, the temperature for molten steel and liquid iron is one of the most important parameter.

10. 简述了计算机在熔炼工艺上的应用、富氧送风、铁液脱硫技术的情况。

The application of computer to the melting process, oxygen-enriched blast and desulphurization technique was briefed.

11. 结果表明：硅铁浸入铁液至完全熔化分为两个时期，即铁壳期和熔化期；

Two separate periods are identified:the iron shell period and melting period, after immersion of ferrosilicon into liquid iron.

12. 对高铬铸铁铁液分别用包底冲入法和瞬时变质处理两种方法进行变质处理。

High chromium cast iron melt was modified by instant modification and pour-over modification from the bottom of the ladle.

13. 在生产灰铸铁时，加入微量锑可防止铁液质量波动，提高抗拉强度和耐磨性。

When producing gray iron, it is possible by adding trace antimony to prevent quality fluctuation of molten iron and increase tensile strength and wear resistance.

14. 以碳管炉为加热体在氩气保护下研究了铁液中镓含量对碳的饱和溶解度的影响。

The relation between Ga content in the molten iron and the saturated solubility of carbon at various temperatures.

15. 介绍了在内蒙一机集团第十分公司用喂线法对铁液进行球化-孕育处理的结果。

Introduced the result of nodularization-inoculation treatment for iron melt by using cored wire injection process in the Tenth Branch Company of Inner Mongolia no.

16. 介绍了增碳剂在铁液中溶解的机理和目前主要采用的投入法和喷粉法增碳工艺。

This paper presents the process of getting the qualified molten iron through melting scrap, carburant and moderate cast pig iron, which offers a new way for producing ductile iron.

17. 研究利用固定点技术测定一定温度和氧分压下铁液与单晶体氧化镁之间的接触角。

In this study the contact Angle between liquid iron and single crystal magnesium oxide substrate was measured by the sessile drop technique at constant oxygen partial pressure and temperature.

18. 通过分析浇不足缺陷产生的原因，认为是铁液压力头小，铁液末端温度低所造成。

It was analyzed that the causes of the defects of misrun in oven door. The main factor effecting on the small pressure in molten iron was low temperature molten iron.

19. 业已查明，缺陷是由于采用冷冒口工艺所致，因为冷冒口实际上起排放冷铁液作用。

It has been found out that the defect was caused by adopting the foundry method with a cold riser which actually acted as a cold metal bleeder.

20. 目前，在炼钢、炼铁的行业中，钢水或铁液的温度是决定炼钢或炼铁的重要参数之一。

During smelting steel and iron, the temperature of molten steel and liquid iron is one of the most important parameters in steel trade.

21. 红硅石作为一种新型的修炉材料，提高了炉衬寿命，稳定了铁液质量，降低了生产成本。

As a new type of line material, red-silica powder can increase the life of furnace liner, assure melting iron quality, reduce production cost.

22. 提高铁液的碳当量、增加孕育剂量和降低铸态组织的渗碳体数量，均有利于增加石墨球数量。

Adding of carbon equivalent and the amount of inoculant can reduce the amount of as cast carbide and increase the number of nodular graphite.

23. 叙述化学成分、孕育工艺、铁液温度及浇注系统等因素对薄壁球铁铸件缩孔和缩松形成的影响。

The influence of chemical composition, inoculation process, temperature of molten iron and pouring system on the formation of shrinkage cavity and porosity was described.

24. 在一定的铁液深度和铁液硫含量时，金属镁粒铁水脱硫时镁的利用率随镁粒的粒径增加而减小；

More bigger of the radius of solid magnesiums are, more longer of the residence time and the rate of the magnesium bubble become, and little of the mass transfer coefficient are in the hot metal.

25. 应用离心铸造工艺生产球墨铸铁管，连续快速提供化学成分和温度均合格的优质铁液是生产的关键环节之一。

One of keys of production of centrifugal casting pipe of s. g. iron is continuous and fast delivery of qualified base iron with proper chemical composition and temperature.wWw.weNtiyI.com

26. 指出在生产这类复杂零件时，要将缸体渗漏废品率控制在0.5%以下时，铁液中铅的含量要控制在0.0008%以下。

It points that the lead tolerance in molten iron should be under 0.0008% if the reject rate is controlled under 0.5% in casting the complicated engine cylinders.

27. 指出在生产这类复杂零件时，要将缸体渗漏废品率控制在0.5%以下时，铁液中铅的含量要控制在0.0008%以下。

It points that the lead tolerance in molten iron should be under 0.0008% if the reject rate is controlled under 0.5% in casting the complicated engine cylinders.