钢屑用英语怎么说，钢屑的英文翻译

词语导航

基本信息

词语：钢屑

繁体：鋼屑

拼音：gāng xiè

英语翻译

【机】 steel scrap

相关词条

1.steelshaving  2.steelscrap  

分词翻译

钢的英语翻译：

steel
【化】 steel
【医】 steel

屑的英语翻译：

bits; crumbs; fritter; scraps; tailing; trifling
【医】 ramenta

翻译例句

1. 介绍了钢屑中铜的测定方法。

It introduces the method of determining copper content in steel chips.

2. 本文简述了以高炉炼铁所用的酸性铁精矿球团代替钢屑冶炼硅铁的试验过程。

The test process of smelting ferrosilicon using acid iron concentrate pellet which is raw materials for blast furnace iron-making instead of steel cuttings is briefly stated.

3. 多数钢屑集中在一个区域，而且几乎所有的其他部件都覆盖上了细细的灰尘。wWw.WeNtiYi.Com

Most of the shavings were concentrated in one area, Tani said, and nearly everything else was covered with a fine dust.

4. 所有在比赛期间，意大利的防守者拥挤在攻击者附近象钢屑子拥挤在磁铁附近。

All during the tournament, Italy"s defenders crowded around attackers like iron filings around a magnet.

5. 太空行走的宇航员以前对接头曾进行过几次检查，甚至收集了钢屑样品回地球分析。

Spacewalking astronauts inspected the joint several times before and even collected samples of the steel grit for analysis back on Earth.

6. 铁屑挤压机是一种将CNC车床加工下来的铁屑、钢屑、铝屑等挤压成固定尺寸、便于转运的包块的专用设备。

The extruding machine for iron scrap is a special equipments which is used to squeeze iron, steel and aluminum scraps produced from the CNC lathe to a solid piece for quick conveyance.

7. 磨刀部分采用高硬度的硬质合金材料，将刀具表面的金属以钢屑的方式去除，磨刀时用力易于掌控，从而将较钝的刀锋快速修正成型。

The whetting part is made of high rigidity metal, will remove the knife"s surface metal by steel scurf, easy to control when whetting, and then fast shape the dull blade.

8. 高温磨损机理为氧化物疲劳剥落磨损，精铸热锻模具钢磨损磨屑为厚大块状，而H13钢磨损磨屑以条状为主。

The high temperature wearing was due to the fatigue delamination of the oxide, the lump wear debris were revealed on the precision cast steel, and the bar wear debris on H13 steel.

9. 根据三维断屑槽切屑折断数学模型，建立了适合精车不锈钢的三维复杂槽型设计方法及开发流程。

It is based on the mathematic model, and it has been established the 3-d grooves designing method and developing process for finish cutting stainless steel.

10. 根据三维断屑槽切屑折断数学模型，建立了适合精车不锈钢的三维复杂槽型设计方法及开发流程。

It is based on the mathematic model, and it has been established the 3-d grooves designing method and developing process for finish cutting stainless steel.