
词语导航
基本信息
词语:铸漏
繁体:鑄漏
拼音:zhù lòu
英语翻译
【机】 bleed; break out; run-out
分词翻译
铸的英语翻译:
casting; founding
漏的英语翻译:
leak; leave out; seep; spillage; water clock
【机】 leak; leakage; leaking
翻译例句
1. 本文就实际生产中出现的连铸漏钢事故,从操作、设备、工艺三方面进行了一些分析探讨并提出解决的对策。
Based on an analysis of the out-breaking cases met in practical production, measures of preventing the accident are proposeding terms of the operation, equipment and process variables.
2. 铸坯裂纹漏钢在连铸生产过程中经常发生。
The billet crack breakout would take place often in the process of continuous casting.
3. 介绍了连铸粘结性漏钢产生的机理和过程,以及宝钢利用人工神经网络技术建立的一套新的漏钢预报系统。
This article presents the mechanism and process of sticking breakout occurring, as well as the newly built prediction system for sticking breakout in Baosteel based on neural network technology.
4. 在拉速提高的条件下,必须优化结晶器内流场以适应稳定生产的需要,防止气孔、拉漏等铸坯缺陷的产生。
Fluid flow in the mould must be optimized in order to improve the internal and surface quality of the slabs while increasing the casting speed.
5. 连铸坯与结晶器间摩擦力是反映铸坯表面质量、优化工艺参数和进行拉漏预报的有效参数。
The friction between billet and mold is an effective parameter reflecting billet surface quality, optimizing technologic parameters and predicting breaking out.
6. 众所周知漏钢是连铸生产中最为严重的生产事故,造成巨大的直接和间接经济损失。
It is well known that breakout is the most serious accident in casting, it will cause a huge direct or indirect economic loss.
7. 剖析了连铸结晶器粘结性漏钢的基本特征,利用热电偶,提出一种新的漏钢诊断预报模型。
The basic feature cohesiveness steel leakage of crystallizer in continuos casting process is analyzed. By using thermocouples, a new model of steel leakage diagnosis forecast is stated.
8. 从而验证了严重的结晶器磨损是连铸坯产生偏角区内裂纹乃至漏钢事故的重要原因之一。
These results verify that the severe mold wear is one of the most important reasons that induce the internal crack and even the breakout at the off-corner of billet.
9. 应用新型的稀土处理钢用保护渣没有发生拉漏事故,并提高了铸坯表面质量。
Break out accidents have never occurred and surface quality of slabs has been improved since introduction of this new type of mould flux into continuously casting the rare earth treated steel.
10. 在连铸过程中结晶器的传热速率对铸坯的表面质量和防止漏钢都具有十分重要的影响。
The rate of heat transfer in mould affects significantly on the surface quality of slab and protection of steel breaking in continuous casting.
11. 针对小方坯连铸高效化改造后拉漏率高的问题 ,分析了造成漏钢的原因 ,介绍了所采取的对策及取得的效果。wWW.weNtIyI.CoM
The reasons of continuous caster leaking are analyzed aiming to the problem of high leaking rate after reforming the small billet cast to improve its efficiency.
12. 漏钢预报系统属于高效连铸生产的关键工艺和装备。
Breakout prediction system is a key technical equipment of high efficient continuous casting technique.
13. 漏钢预报系统属于高效连铸生产的关键工艺和装备。
Breakout prediction system is a key technical equipment of high efficient continuous casting technique.
版权声明:问题易所有作品(图文、音视频)均来源网络,版权归原创作者所有,与本站立场无关,如不慎侵犯了你的权益,请联系我们告知,我们将做删除处理!
