
词语导航
基本信息
词语:焊接检查
繁体:焊接檢查
拼音:hàn jiē jiǎn chá
英语翻译
【化】 weld inspection; welding inspection
相关词条
1.weldinspection分词翻译
焊接的英语翻译:
seal; solder; weld【医】 solder; soldering
检查的英语翻译:
check up; examine; inspect; censor; check; look-over; inspection【计】 inspectoscope
【医】 docimasia; examination; inspection
【经】 check; check up; checking; examination; examine; inspection; monitoring
survey
翻译例句
1. 焊接电子部件还会产生有害气体,但管理人员拒绝打开通风设备,安全检查人员在场的情况下除外。
The welding of electronics parts also produces toxic gases, but management refuses to turn on the ventilation system, except when safety inspectors are present.
2. 然后你可以做之前检查最后焊接的一切运作。
Then you can check the operation of everything before doing the final welding.
3. 在铺管船上的各种站—焊接、检查、覆盖层站等—在铺管船上处于相同的位置。
All of the stations on the barge-welding, inspection, coating-remain in the same position on the barge.
4. 检查各焊接部位的情况特别是断绳安全装置和吊笼安全插块部位的焊缝情况。
Test the condition of all the welding parts especially rope-break safety instrument and welding seam of suspension coop safety inserting block.
5. 介绍了钛制叶轮的焊接工艺和制造过程,说明了焊接部位的检查方法及检查结果。
The paper introduces the welding procedure and fabrication process of titanium alloy wheel, indicates the inspection method and quality result of welding location.
6. 如果试件不符合7.5规定的外观检查或非破坏性检查的要求,应再取一个试件进行焊接,并进行同样检查。
If the test piece fails to comply with any of the requirements for visual examination or NDT specified in 7.5, one further test piece shall be welded and subjected to the same examination.
7. 加强构件的非水密焊接接合和填角焊应该在检查完分段后进行喷漆。
Non-watertight weld joints and fillet welding for stiffening member shall be painted after block inspection.
8. 步骤之一,焊接过程是检查叶片温度。
Step one of the welding process is checking the blade temperature.
9. 货舱口围板焊接后焊缝检查。
Inspecting welding seam of hatch coaming after welding.
10. 在工厂内及分包商处监督并检查钢结构和焊接工作的质量。
Perform monitoring, inspection and quality control at in-house and sub-contractor steel fabrication and welding section .
11. 尺寸检查应在组对、焊接前和最终焊接完成后立即进行并记录。
The dimension inspection should be finished before the assembly and the welding and after the final welding, and it should be recorded immediately.
12. 这种封装使焊接更加可靠,便于进行焊锡质量检查和用示波器探头接触引线。
This provides more reliable soldering, solder-quality inspection and easy access with oscilloscope probes.
13. 二滩水电站已全部投运的6台机转轮经停机检查,现场焊接的主焊缝无裂纹。
The runners of 6 operated generating unit of Ertan Hydro Station have been checked and no crack on the primary weld of the field welding position is observed.
14. 焊缝导向弯曲试验的目的是检查焊接接头的完好性和塑性以及材料的焊接工艺和表面缺陷。
The purpose of weld guide bending test is to detect plasticity of welding joint, welding process and surface defects of materials.
15. 当第一个完全焊接,检查其他它,以便对最后一分钟的调整可。
When the first one is completely welded, check it against the the other so that last minute adjustments can be made.
16. 采用先进的双丝窄间隙埋弧焊设备和专用焊接工艺,成功地焊接了大厚壁高压蓄势器,质量检查全部合格。
An advanced double wires narrow gap SAW technique, equipment and special procedure have been used to weld high pressure storage tanks successfully with high quality welding joints.
17. 手头有二氧化碳或干粉灭火器,检查焊接操作的地方已经进行了至少30分钟后,工作已经完成,任何残留的火灾风险。
Have co2 or dry powder fire extinguishers at hand, check areas where welding operations have been undertaken at least 30 minutes after work has been completed for any residual fire risks.
18. 可以用氩弧焊(GTAW)制备气焊缝,这种焊接方法可以用来测试材料的可焊接性,检查气体保护的使用以及焊接参数的设定。
An autogenous weld is produced by GTAW and can be used to test material weldability and gas shield usage, and to set welding parameters.
19. 最后将展示的是TIG焊接法质量的等级分类的不同工艺参数的加工实验检查结果。
Finally, an experimental verification of the classification results for TIG weld quality with different process parameters is shown.www.WeNtIYI.CoM
20. 在进行跑车试验前,先检查焊接质量,如焊接接头所包括的焊缝、熔合区和热影响区等,以设定整个工艺流程;
The frame material and the welding procedure can be set according to the pre-judgement carried out by combining the CAE analysis with the residual stress distribution before welding.
21. 研究了用X射线探伤方法检查铠装热电偶焊接质量,介绍了焊接仪器、透度计设计和探伤实验方法,讨论了铠装热电偶X射线探伤实验结果。
The welding quality of sheathed thermocouples was investigated by X ray testing. The design of penetrometer, the testing method, and the testing results were introduced.
22. 首先,我认为它是开关的机制,所以我把它拆开了几次,检查一切,重新焊接,看起来狡猾的东西,但它从来没有固定的问题。
First I thought it was the switch mechanism, so I pulled it apart a couple of times and checked everything, and re-soldered anything that looked dodgy but it never fixed the problem.
23. 仔细检查发现雕像的头部是铸好后再焊接上去的。
Careful inspection showed that the statue"s head had been cast separately and soldered in place.
24. 过滤器之纵向和周围焊接缝是染色探伤检查,其它将以X-射线和/或超音波检查。
Longitudinal and circumferential weld seams are PL inspected for class150#, for other classes will be inspected with X-Rays and/ or US.
25. 配合采购工程师检查和审核日常焊接供应商;
Check audit welding supplier in coordination with sourcing engineers ;
26. 然后一个机械臂将焊接好的外壳打落在工作台上并由一名工人检查焊点。
Then a mechanical arm knocks them down to a worker who inspects the welding job.
27. 如果露出了焊接点,检查是否形成了裂纹。
If the soldered joints are exposed, check for visible signs of crack formation.
28. 吊耳及凸耳的材料及同壳体焊接的程序及检测方法应仔细检查。在进行吊耳及凸耳的设计时应考虑最小冲击系数1.25。
The shock factor of 1.25, as minimum, shall be considered in the design of lugs and shell.
29. 吊耳及凸耳的材料及同壳体焊接的程序及检测方法应仔细检查。在进行吊耳及凸耳的设计时应考虑最小冲击系数1.25。
The shock factor of 1.25, as minimum, shall be considered in the design of lugs and shell.
版权声明:问题易所有作品(图文、音视频)均来源网络,版权归原创作者所有,与本站立场无关,如不慎侵犯了你的权益,请联系我们告知,我们将做删除处理!
