
词语导航
基本信息
词语:齿隙
繁体:齒隙
拼音:chǐ xì
英语翻译
【化】 back lash
相关词条
1.toothspace 2.gearbacklash 3.backlash分词翻译
齿的英语翻译:
tooth; tine【医】 dens; dent-; dentes; denti-; dento-; odont-; odonto-
隙的英语翻译:
crack; crevice; gap; interval; opportunity; rift【化】 opening
【医】 gap; space; spatia; spatium; split
翻译例句
1. 将盆形齿轮往回转,然后读取圆周齿隙。
Turn the crown wheel back and read off the circumferential backlash.
2. 在得到合适的齿隙后,执行齿轮接触分析程序。
After the proper backlash is achieved, perform the Gear Contact Analysis procedure.
3. 在达到合适的齿隙后,执行齿轮接触印痕图形分析过程。
After the proper backlash is achieved, perform Gear Contact Pattern Analysis procedure.
4. 使用千分表检查齿轮之间齿隙,与安装图纸上的数值进行比较。
Check the backlash of gears with dial gage and compare with values shown on the assembly drawing.WWw.WeNTiyI.COm
5. 同时,阐述了实现齿隙误差补偿的软件方法,并采用软件方法加以实现。
Meantime, an algorithm to the error compensation of the tooth clearance is implemented.
6. 机电伺服系统的齿轮传动装置,其齿隙不仅影响系统的伺服精度,更影响系统的稳定性。
The gear clearance in the driving device of the electromechanical servo system shall affect not only the servo accuracy of the system but also its stability.
7. 火炮伺服系统传动链存在传动齿隙,齿隙是影响火炮伺服系统动态性能和稳态精度的重要因素之一。
Transmission chain of gun servo system has backlash, it is one of the important factors that affect dynamics performance and stable precision of gun system.
8. 本文运用热弹性力学原理,分析了温度变化对啮合齿轮侧隙的影响以及对齿厚偏差选择的影响。
Based on the thermal elastic mechanics, the influence of temperature change on the normal backlash was analyzed, and the deviation of teeth width was calculated.
9. 最后,提出了一种新的侧隙和齿厚偏差选择规范。
And finally a new norm is put forward for selecting backlash and tooth thickness deviation of gears.
10. 混合式步进电动机内部是径向和轴向混合的磁系统,气隙或齿层的磁场沿电机轴向非均匀分布,将问题简化为二维磁场后要得到精确结果有一定的困难。
There are mixed magnetic field system of axial and radial in hybrid stepping motors, and the magnetic field in the gap (or teeth layer)is distributed uneven along the axial direction.
11. 利用轮齿接触分析与齿轮啮合原理,建立了齿面均匀研磨与定点研磨控制的几何运动模型,经滚检检验,该模型能对齿面研磨位置与侧隙进行较准确的控制。
The rolling tests prove that this setup model can control precisely the displacement of the lapped area in the tooth surface and keep the even backlash.
12. 利用轮齿接触分析与齿轮啮合原理,建立了齿面均匀研磨与定点研磨控制的几何运动模型,经滚检检验,该模型能对齿面研磨位置与侧隙进行较准确的控制。
The rolling tests prove that this setup model can control precisely the displacement of the lapped area in the tooth surface and keep the even backlash.
版权声明:问题易所有作品(图文、音视频)均来源网络,版权归原创作者所有,与本站立场无关,如不慎侵犯了你的权益,请联系我们告知,我们将做删除处理!
