焊前预热用英语怎么说,焊前预热的英文翻译


词语导航

基本信息

词语:焊前预热

繁体:焊前預熱

拼音:hàn qián yù rè

英语翻译

【化】 weld preheating

分词翻译

焊的英语翻译:

solder; weld
【电】 soldering

前的英语翻译:

former; forward; front; preceding; priority
【医】 a.; ante-; antero-; fore-; pro-; proso-; ventri-; ventro-

预热的英语翻译:

warm-up
【机】 preheat; preheating

翻译例句

1. 请您提供焊前预热和焊后预热处理的规范。wWw.WeNTiyi.coM

Please give the standards of the preheat before welding and those of the heat-treatment after welding.

2. 通过焊前预热、层间温度控制及焊后热处理等手段获得了满足质量要求的焊缝。

With the methods of the pre-heating before welding, controlling the interlaminar temperature and the heat treatment after welding, the welds that satisfy the quality specifications can be available.

3. 但由于室外温度比较低,要求预热到室温后再进行焊接操作的焊前预热可不作记录。

However, if outdoor temperature is comparatively low, the records preheating aren"t required for the welding operation preheating to room temperature.

4. 试验表明,采取焊前预热,焊后热处理的TIG焊工艺进行焊接可以减少焊接缺陷的产生。

The experiment results show that the welding defects can be decreased by using preheat and post-weld heat treatment.

5. 结果表明:采用焊前预热和焊后热处理的焊接工艺方案所获得的焊接接头比不采用以上措施获得的焊接接头更为合理,应用更安全、可靠。

The result shows that it is more reasonable, safe and reliable to adopt procedure with warm up before welding and post heat treatment after welding.

6. 通过采取焊前预热、控制焊接线能量和层间温度、焊后保温缓冷等工艺措施,并采用相应的检测方法,保证了胺液吸收塔的低温焊接质量。

According to the test, the welding interlayer temperature of X60 pipeline in the normal and low temperature is analyzed in order to study the influence of its variable range on welding quality.

7. 从焊接材料的选用,焊前预热、焊接过程和焊后热处理的控制几个方面,着重介绍了ZY6400/12.5/28型液压支架的焊接工艺。

The paper introduces welding technology of type ZY6400/12.5/28 hydraulic support, from several respects of selecting materials preheat before welding, welding process and so on.

8. 焊前不预热不产生裂纹、可改善劳动条件,降低工艺成本,具有显著的经济效益和社会效益。

The electrode has the following advantages : a high resistance to cracking, low cost, high economical profit and society significance.

9. 采用碱性药皮焊条和焊前接头预热的施焊方法,焊接的空间管道接头热应力小。

For overhead pipeline, welding with basic-compound coated electrodes and pre-welding heating of the joint will reduce the joint thermal -stress.

10. 焊接性不好,易产生裂纹,焊前应预热。

Welding is not good, easy to crack, preheating before welding shall be.

11. 焊接性差,焊前应预热。

Poor welding preheating before welding, should be.

12. 修理前,围绕兼顾解决焊接性、应力和变形问题,结合实际施工条件制定了以手工钨极氩弧焊、镍基焊丝、焊前低温预热、焊后锤击焊缝为要素的冷堆焊工艺。

The method of surfacing welding sealing strip was adopted to repair the deformation of the flange joint surface of the high and intermediate pressure outer casing .

13. 该焊条耐磨性能好,焊前不预热,可用于轧辊的堆焊。

The welding rod has good wearing resistance and needn"t warm before welding, which may be used to the surfacing of the roller.

14. 焊接性不好,适于电阻焊接,焊前需预热,焊后需回火处理。

Good weldability, suitable for resistance welding, preheating before welding required, be tempering after welding.

15. 焊接性不好,适于电阻焊接,焊前需预热,焊后需回火处理。

Good weldability, suitable for resistance welding, preheating before welding required, be tempering after welding.

版权声明:问题易所有作品(图文、音视频)均来源网络,版权归原创作者所有,与本站立场无关,如不慎侵犯了你的权益,请联系我们告知,我们将做删除处理!