剪切载荷用英语怎么说,剪切载荷的英文翻译


词语导航

基本信息

词语:剪切载荷

繁体:剪切載荷

拼音:jiǎn qiē zǎi hé

英语翻译

【化】 shear load

分词翻译

剪切的英语翻译:

【计】 cut
【化】 shear; shear cut; shear(ing); sheared

载荷的英语翻译:

load
【化】 load

翻译例句

1. 介绍板在单向压缩和剪切载荷作用下的屈曲模态、临界载荷和平衡路径。

This chapter indicates buckling modes, critical load and equilibrium path of plate under axial compression and shear load.

2. 理论分析证明,在剪切载荷作用下裂纹扩展是由于拉伸应力引起的,并非剪切破坏。

Theoretical study shows that the crack extension under shear loading is caused by tensile stress, and it does not belong to shear fracture.

3. 点焊试样剪切试验中存在脱壳式、剪断式和压断式三种断裂模式,所对应的熔核尺寸和剪切载荷依次增加。

There are three fracture modes in shearing tests, i. e. , exuviation, shear and crush fractures, with nugget dimensions and shearing loads increasing in turn.

4. 本研究利用“剪切梁”模型,研究了在定常侧压力和周期性的反平面剪切载荷共同作用下,层间界面的破坏规律。

In this study, the interface failure under the joint action of constant compression and periodical anti-plane shear were investigated.

5. 本研究利用“剪切梁”模型,研究了在定常侧压力和周期性的反平面剪切载荷共同作用下,层间界面的破坏规律。

In this study, the interface failure under the joint action of constant compression and periodical anti-plane shear is investigated.

6. 为了建立波纹板屈曲的数值分析方法,对复合材料波纹板在剪切载荷作用下的屈曲进行试验、工程算法和有限元方法研究。

The main purpose of this paper is to establish a numerical method for the buckling of composite corrugated panel under shear loads via experiments and computations.Www.wENTIyI.cOM

7. 剪切弹簧承担大部分垂直方向的载荷,降低震动频率。

The shear spring bears most of the vertical loading, which decreases the vibration frequency.

8. 在分析动载荷下的应力和变形时,除考虑横向剪切效应外,还须考虑微段的惯性力和阻尼力矩。

In the analysis of the stress and deformation under dynamic loading, the inertia force and damping moment should be considered in addition to the transverse shear effect.

9. 作为算例,给出了环形板在中面均匀径向压力和剪切力作用下的临界载荷。

As examples, the critical loads of annular plates under the uniform radial pressure and shear forces are given.

10. 本文针对船型的特殊性,采用了适宜的载荷预报方法,妥善地解决了该船体的总纵强度、剪切强度及横向强度。

In accordance with the special characteristics of this type of ship, a proper load predication method is adopted for hull longitudian strength, shear strength and transverse strength.

11. 采用有限元计算编码abaqus模拟了钨合金圆台试件在冲击载荷下的变形和剪切局部化行为。

The deformation behavior and shear localization in truncated conic specimens of tungsten heavy alloys under impact loading are simulated by the finite element code ABAQUS.

12. 预测的强度能够反映出横向剪切效应的影响,其影响只与载荷大小有关,而与跨高比无关;

The calculated strength could show the affection caused by transverse shear effect and the affection had only relation to the loading value and no to the ratio of span-height.

13. 剪切失效是强动载荷作用下结构失效的重要模式。

Shear failure is an important mode of dynamic failure of structural members under impulsive loading.

14. 数值算例表明,对于复合材料旋转壳,横向剪切变形使其临界载荷降低;

The examples show that the critical load of composite shells of revolution will decrease when considering the transverse shear deformation.

15. 结果清楚地显示,深承台板的载荷传递机制与相应的双向剪切破坏模式。

The results clearly illustrate the load transfer mechanism in the deep pile cap and the subsequent failure mode of two-way shear.

16. 剪切对轴压稳定临界载荷的影响,可用微分方程来解决。

The effect of the shear deformation on the buckling load can be calculated by solving the differential equation for the buckling broblem.

17. 在分析单桩的载荷传递机理、单桩的破坏模式的基础上,重点探讨了单桩沉降的载荷传递法和剪切变形法。

On the basis of load transfer mechanism and destruction patterns of single pile, load transfer method and shearing deformation method for subsidence computing of single pile are mainly discussed.

18. 最后,本文以实例分析讨论了横向剪切变形、开孔大小、线布载荷位置和几何参数对临界载荷的影响。

Finally, some examples are given to show the effect of shearing deformation, the hole size, the position of linear load and the geometrical parameter on the critical load.

19. 在水力侵蚀作用下黄土破坏实质上是剪切破坏,但土壤抗剪强度表现形式与外载荷作用形式密切相关。

The destruction of soil is shearing in effect, but the representation of soil anti-shearing strength is closely related to the mode of external load action.

20. 包括拉伸、剪切以及弯曲等载荷。

Some of the loads include tensile, shear and bending.

21. 应用广义阶梯函数来表示载荷,然后再将其展开成傅立叶级数形式,推导出纵向剪切问题的位移计算公式。

The Fourier series of load is given by using generalized step function and the displacement formula of the longitudinal shear problem is derived.

22. 文末还说明了,利用测定的正交层间剪切强度来分析正交铺设层合板短梁的极限载荷是合适的。

Furthermore, it indicates that it is suitable to analyse the ultimate load of a cross-ply laminated short beam with the measured shear strength of cross-interlamination.

23. 文末还说明了,利用测定的正交层间剪切强度来分析正交铺设层合板短梁的极限载荷是合适的。

Furthermore, it indicates that it is suitable to analyse the ultimate load of a cross-ply laminated short beam with the measured shear strength of cross-interlamination.

版权声明:问题易所有作品(图文、音视频)均来源网络,版权归原创作者所有,与本站立场无关,如不慎侵犯了你的权益,请联系我们告知,我们将做删除处理!