
词语导航
基本信息
词语:阀片
繁体:閥片
拼音:fá piàn
英语翻译
【化】 valve plate
分词翻译
阀的英语翻译:
clique; valve
【化】 valve
【医】 limen; limina; valve
片的英语翻译:
flake; parcel; partial; patch; piece; slice
【计】 slice
【医】 disc; disci; discus; disk; flap; piece
【经】 card
翻译例句
1. 磁性阀座、覆膜阀片组合设计。
Magnetic valve seat, diaphragm and valve plate combined design.
2. 对高压阀片进行的谐波试验结果验证了以上分析结果。
These analysis results are verified by tests of high voltage valve elements.
3. 提出了一种研究油气弹簧环形阀片大挠曲变形的方法。
A research method of the large deflection of the throttle slice of the hydropneumatic spring was presented.
4. 排除:清除杂物,更换已损坏的橡皮垫,改变阀片方向;
Excluded: debris removal, replacement of damaged rubber pad to change the direction of the valve;
5. 氧化物避雷器;阀片;阻性电流;红外检测;工频参考电压。
MOA; valve piece; resistive current; infrared detection; frequency reference voltage.
6. 采用机械优化设计方法并结合阀片的几何形状进行优化设计。
The machine optimization design method in combination with the reed valves geometry shape was employed to optimize the design.
7. 用工程断裂力学研究了非金属夹杂物尺寸对阀片疲劳寿命的影响。
An investigation has been made on the influence of the dimension of non-metallic inclusions on valve fatigue life according to engineering fracture mechanics.WWw.WEntiYI.coM
8. 节流阀片厚度是减振器的关键参数,决定和影响减振器的阻尼特性。
The throttle slice thickness is the key factor that affects vehicle vibration characteristic.
9. 用优选的工艺参数对阀片进行表面强化与防蚀处理,获得了较好的效果。
Fairly good results have been obtained by using optimum parameters for surface strengthening and anti corrosion treatment of valve plate.
10. 根据活塞压缩机的工作过程和阀片的运动方程建立了其工作的模拟模型。
A working process simulation model was established in accordance with the dynamic process of reciprocating compressor and the valve dynamic equations.
11. 提出了减振器环形节流阀片受局部变载荷作用时挠曲变形量的一种研究方法。
A research method for the deflection of throttle slice under the local distribution of variable load is presented.
12. 针对工艺用压缩机气阀的失效形式,对损坏的阀片进行了断口及静态应力分析。
According to the failure style of the air valve of industrial compressor, the fracture and static stress are analyzed.
13. 山特维克公司介绍2。山特维克钢带范围3。山特维克阀片钢带4。技术讨论。
Sandvik Company Introduction 2. Sandvik Strip Area 3. Sandvik flapper valve production 4. Technical discussion.
14. 对性地设计了红外温度传感器阵列,为解决阀片温度测量问题开辟了新的途径。
Specifically design an infrared temperature sensor array and develop a new method to solve the problems of valve piece temperature measurements.
15. 选取了一种高效的橡胶薄膜阀片,设计并制作了具有较高输出能力的双腔泵样机。
A high efficient rubber membrane valve was made, and double-chambered PZT pump with high output capability was designed and fabricated.
16. 分析了减震器中阀片的工艺特点,介绍了其模具结构的确定原则和模具的加工方法。
The technological characteristics of the valve of the shock absorber were analyzed. And the principle for determining the structure of the die and the method for processing the die were introduced.
17. 对比结果表明,叠合式节流阀片的设计原则、当量厚度和应力计算方法是准确和有效的。
The compared results show that the design scheme is effective and the formulas for equivalent thickness and maximum stress of the throttle multi-slice are accurate enough.
18. 根椐大型压缩机气阀阀片的失效形式,分析了气阀弹簧、压缩介质等因素对气阀寿命的影响。
The effects of the factors such as valve spring and compression agent on the service life of valves were analyzed based on the damage forms of valve sheets of large-scale compressors.
19. 对该系统中气阀阀片的运动规律进行了模拟,对可调回流气阀的机构和加载力设计起了指导作用。
The simulation of the valve plate has been worked, and it can be used as the direction for the design of SCCS and the unloader force.
20. 综合分析了阀片的失效原因、机理,并进行了对阀片边缘实施滚磨倒角来提高其疲劳寿命的实验研究。
The cause and mechanism of valve failure are analyzed, and the method of tumbling chamfer is studied to improve service life of the valves.
21. 除具有纯滚流特点的S1阀片位置外,缸内气体斜轴涡流运动强度与单边气道截面被遮住的面积成正比。
Lastly, the strength of inclined-axis swirl is directly proportional to the Shadowed area of the single channel except for the S1 valve position where the in-cylinder motion is only tumble.
22. 定义了阀片电压偏差率并以此为目标函数,建立该目标函数与各均压环环直径和悬挂高度的拟合多项式关系。
The ratio of voltage warp(RVW) for the varistor is defined to simulate a polynomial of every diameter and suspended heights of the grading ring.
23. 实践证明:按照上述原则设计的回路可用于对避雷器阀片、压敏电阻及浪涌保护器SPD进行冲击电流检测。
The fact shows that the designed circuits can be used in impulse current test for arrestors, varistors and SPD.
24. 根据自主研发阻尼可调油气弹簧的结构形式,分析了叠加节流阀片的挠曲变形量,给出系统流量分配的等效关系。
The deflections of throttle slices were analyzed and the equivalent relations of flux distribution were deduced according to the structure of self-designed hydro-pneumatic spring.
25. 当阀片两侧的压差随时间变化时,阀片的启闭与压差的变化之间存在一定的相位差,有可能引起泄漏甚至反向流动。
When the pressure difference changes with time, a phase shift will occur between the transient pressure difference and displace of valve flap, which could cause leakage and even reverse flow.
26. 第四章首先测试了阀片的启动压力、阀口泄漏量、流量特性以及压力响应时间,然后对实验结果进行了分析和比较。
Chapter 4 first test the starting pressure of valves, leakage of valve port, flow characteristic and response time, and then the experimental results are analyzed and compared.
27. 利用开阀速度和开阀压力建立油气弹簧节流缝隙设计公式,并对叠加阀片和调整垫圈对节流缝隙的影响进行了分析。
The design formula of throttle aperture of hydro-pneumatic spring was established according to the relationship between pressure and flux.
28. 运用正交试验设计方法在田间进行灌水试验,结果表明:波涌阀前调节阀入口压力是影响波涌阀阀片转换的主导因素;
The main factor was the entrance pressure of the regulating valve before surge valve to influence the conversion of valve slice of surge valve.
29. 将透气阀圆形弹性阀片的应用结构简化为了环形结构,建立了阀片受均布载荷时的力学模型,并研究了阀片的弯曲变形。
The circular elastic slice of degassing valve was simplified as ring mechanics and the mechanic model of the slice under uniformly distributed load was established to investigate its deformation.
30. 研制了一种检测氧化锌避雷器阀片的重复频率充放电装置,采用L C恒流充电技术,通过电压反馈法控制充放电运行过程。
The charging technique with L-C constant-current converter is adopted, and the repeated charging and discharging process of the device is controlled by voltage feedback.
版权声明:问题易所有作品(图文、音视频)均来源网络,版权归原创作者所有,与本站立场无关,如不慎侵犯了你的权益,请联系我们告知,我们将做删除处理!
