角旋用英语怎么说,角旋的英文翻译


词语导航

基本信息

词语:角旋

繁体:角旋

拼音:jiǎo xuán

英语翻译

【医】 angular rotation

分词翻译

角的英语翻译:

corner; angle; cape; contend; horn; wrestle; role
【医】 angle; anguli; angulus; Broca"s angle; cornu; cornua; gonio-; horn

旋的英语翻译:

screw; spin; whirl; come back; lathe; return; revolve; soon
【医】 administer; spin

翻译例句

1. 旋角羚羊生活在北非洲的撒哈拉沙漠中。

The addax lives in the Sahara Desert of northern Africa.

2. 它对于需要做旋变,自整角,检流计的运动和照明电路测试的仪器,能够在航空电力环境里进行全面的使用特性测试。

Instruments requiring the testing of Resolvers, Synchros, Galvanometric Movements and Lighting Circuits can be fully tested for operational performance in the Airborne Electrical Environment.

3. 给出了在特定条件下非线性旋光附加角的表达式。

The expressions of the nonlinear optical rotation additional Angle in some special conditions are given.

4. 研究表明:由于进料螺旋输送器的作用,在一定的导流叶片角条件下存在着双旋流流场。

It is shown that the existence of central screw conveyer produces the contrary swirl flow under some of the swirl vane Angle condition.wWW.WeNTIYI.COM

5. 该预旋角情况下,进气雷诺数对盘面平均努赛尔特数的影响大于旋转雷诺数。

The cooling flow rate have more effects on average nu number than rotating speed in this pre-swirl Angle.

6. 从理论上证明了改变导程角是控制物料旋留时间的最有效的方法。

It is proved theoretically that changing lead Angle is the best way to control the turn staying time of material.

7. 本文还介绍了为提高复合片钻头经济指标的钻头参数设计问题,如负前角,侧旋角等。

This paper also discusses bit parameter design to improve the economy of PDC bits, such as negative rake Angle and side rotation Angle.

8. 然后介绍了一、二次风速,旋流叶片的导角,一次空气比例系数等参数的选择及制造烧嘴的材料。

Selection of the primary and secondary airflow rate, the guide Angle of the blade, the primary air ratio as well as the material for manufacture of the burner nozzle are given.

9. 旋松阀帽中间的内六角螺丝,并且提起阀帽,正好足够拿走旧阀膜。

Unscrew the Allen screw in the middle of valve cap and lift up the cap just enough to pick up the old diaphragm.

10. 对于旋成体有攻角绕流,本文研究了垂直于物面的横截面上的流态结构。

The topology of flow patterns on cross section perpendicular to the body surface are studied for flows around a body of revolution at angles of attack.

11. 获得了成形角、减薄率、进给比等工艺参数对等效应力、旋压力及内筋成形高度的影响规律,为旋压工艺参数的选择和优化提供了依据。

The rules which various parameters influence spinning force and equivalent stress are obtained and its provide theoretical evidence for choosing the optimal parameters.

12. 旋翼尾流的作用通过自由尾流分析来求解局部的诱导下洗速度以修正翼型攻角。

Rotor wake effects are modeled in the form of a correction applied to the angle of attack along the blades. This correction is obtained by computing the local induced downwash with free wake analysis.

13. 当蜗轮蜗杆的交错角为时,还需保证,而且蜗轮与蜗杆螺旋线旋向必须相同。

When the worm crisscross Angle, still need to ensure that"s too, and worm gear and worm helical screw to must be identical.

14. 本文依据因次分析的基本原理,研究了装煤时旋叶升角的变化函数。

The variable function of vane Angle during loading is studied on the basic principle of dimensional analysis.

15. 根据最佳装煤条件下的试验数据,提出了合理旋叶升角的范围;并从截煤效率考虑,对此范围进行了修正。

A-reasonable range of vane Angle is presented on the basis of experiment data in optimal loading condition, and the range is modified in view of cutting efficiency.

16. 本文对佳木斯地区100例胎尸发旋的位置、方向、旋顶问距及角距正中角度进行了观测。

The hair rotations of 100 fetal corpses over Jiamusi District were observed and their positions, orientations, angles and intervals between head top and the hair rotation were discussed.

17. 建立了旋翼升力线模型和广义尾迹模型,在计算角迹涡线诱导速度时,采用了快速收效方法。

Both lift line model and generalized wake model are founded in this paper. A method is given for calculating induced velocities by a wake vortex line which results in a rapid convergence.

18. 应用五孔感头测定沿程截面内气流的切向角、轴向速度、气流静压和旋流数的分布。

A five hole probe is used for measuring the tangential Angle of flow, axial velocity, static pressure of flow and swirl number in the flow sections of the conveying system.

19. 所述旋流构件为一段带螺旋角的螺旋扭片,所述螺旋扭片的轴向形状为圆形。

A vortex member is arranged on the vortex net board. The vortex member is a spiral twist sheet with a spiral Angle. The axial shape of the spiral twist sheet is circular.

20. 从理论上证明了改变导程角是控制物料旋留时间的最有效的方法。

It is proved theoretically that changing lead Angle is the best way to control the turn staying time of material. Hence the theoretical basis for production practice has...

21. 从理论上证明了改变导程角是控制物料旋留时间的最有效的方法。

It is proved theoretically that changing lead Angle is the best way to control the turn staying time of material. Hence the theoretical basis for production practice has...

版权声明:问题易所有作品(图文、音视频)均来源网络,版权归原创作者所有,与本站立场无关,如不慎侵犯了你的权益,请联系我们告知,我们将做删除处理!