
词语导航
基本信息
词语:曲轴颈
繁体:曲軸頸
拼音:qū zhóu jǐng
英语翻译
【化】 crank journal
分词翻译
曲轴的英语翻译:
【化】 bent axle; crank shaft
颈的英语翻译:
cervical; kink; neck
【医】 cervico-; cervix; colla; collum; der-; dero-; jugulum; neck; trachel-
trachelo-; trachelos
翻译例句
1. 从曲轴颈上拆下活塞和连杆。
Remove piston and connecting rods from crankshaft journals.
2. 连杆的一端与曲轴的连杆轴颈相连,另一端通过活塞销与活塞相连。
The connecting rod is attached at one end to a crankpin on the crankshaft and at the other end to a piston, through a piston pin or wrist pin.
3. 介绍了曲轴连杆轴颈磨削的原理,对其常见的位置误差现象的形成原因进行了分析,并提出了相应对策和办法。
The grinding principle of crankshaft journal is introduced, the formation reason of position error is analyzed in detail, and the corresponding measures are proposed as well.
4. 通过对发动机曲轴轴颈与轴承损坏原因的分析,重点阐述了发动机在使用与维修中预防损坏的措施和方法。
By analyzing reasons for break of engine crankshaft journal and bearing, this paper describes mainly some countermeasures they are break in use and maintenance.
5. 本文简述了一种正在兴起的曲轴连杆轴颈的磨削方法和原理。
The article introduced a grinding method and principle of the journal of crankshaft connecting rod.
6. 在发动机里,机油被供应到旋转在其支承轴内的曲轴和凸轮轴轴颈上。
In the engine, oil is supplied to crankshaft and camshaft journals rotating in their supporting bearings.
7. 在图1-4中,曲轴实际上由以下不同的部分组成,它们分别是:主轴承轴颈、连杆轴颈、曲轴臂、轴承、平衡配量(?)以及飞轮端。
The crankshafts shown in Fig 1-4 is actually made up of various parts such as main bearing journals, rod journal, crank arm, bearing, counter balanced weight and flywheel end.
8. 曲轴:合金钢,全支承、轴颈和圆角淬火。
Crankshaft: Alloy steel with whole bearing supporting and bearing and round corner harden.
9. 提出了两种曲轴齿轮轴颈键槽位置误差的检测方法。WWw.wENTIyi.com
Two kinds of inspection methods of the position error of key slot an gear journal of crankshaft have been proposed.
10. 最后提出了减小曲轴主轴颈径向圆跳动误差的措施。
Finally, the measures to reduce the radial circle run-out error of the crankshaft main journal have be presented.
11. 同样,在进行曲轴轴颈和曲轴轴承配合间隙的测量时,也可以借鉴这种操作技巧。
Similarly, in the crankshaft journal and crankshaft bearing clearance measurements, they can draw on such skills.
12. 曲轴的各轴颈在很高的比压下作高速旋转运动,使轴颈和轴承受到强烈磨擦。
Because the shaft necks whirligig with high speed under high pressure, the shaft necks and bearings endure intense attrition.
13. 针对加工六缸曲轴主轴颈孔、连杆颈直油孔的需要而设计的卧式双面多工位数控钻削组机。
Horizontal double sided NC combined drilling machine is specially designed for the machining of main shaft journal hole and crank arm journal straight oil hole of crankshaft with six cylinders.
14. 利用ANSYS有限元分析软件分别建立曲轴连杆轴颈、主轴颈圆角滚压模型,进行变形分析计算。
The models of the connecting rods and principal axis neck are built, and the finite element analyses have been done to them by using ANSYS engineering software.
15. 可实现一次装夹完成对曲轴连杆颈、主轴颈、止推面批量精密加工。
It can finish precise grinding of crankpin, main journal, and thrust face with one chucking.
16. 本文讨论了内燃机曲轴轴承副的工作状况和磨损,给出曲轴轴颈磨损的计算模型和计算方法。
The operation conditions and wear of crankshaft bearings in internal combustion engine are discussed in this paper. A model and method for calculating the crankshaft journal wear are given.
17. 本文讨论了内燃机曲轴轴承副的工作状况和磨损,给出曲轴轴颈磨损的计算模型和计算方法。
The operation conditions and wear of crankshaft bearings in internal combustion engine are discussed in this paper. A model and method for calculating the crankshaft journal wear are given.
版权声明:问题易所有作品(图文、音视频)均来源网络,版权归原创作者所有,与本站立场无关,如不慎侵犯了你的权益,请联系我们告知,我们将做删除处理!
