高碳合金钢用英语怎么说,高碳合金钢的英文翻译


词语导航

基本信息

词语:高碳合金钢

繁体:高碳合金鋼

拼音:gāo tàn hé jīn gāng

英语翻译

【化】 high-carbon alloy steel

分词翻译

高的英语翻译:

high; high-priced; lofty; loud; tall
【医】 homo-; hyper-; hypsi-; hypso-; per-

碳的英语翻译:

carbon
【化】 carbon
【医】 C; carbon; carboneum

合金钢的英语翻译:

【化】 alloy steel

翻译例句

1. 迄今为止,高碳合金钢材料的焊接理论仍未完善。

Up to now, the welding theory for high carbon alloy steel has not been well established.

2. 在研究的基础上改进了高碳合金钢细长轴的磨削工艺,克服了表面烧伤现象。

The research, has improved grinding technology of high-carbon alloy steel slender axis, and the phenomena of exiguous flaws were overcomed.

3. 本文针对焊缝熔敷金属在高强时,容易开裂问题展开研究,研制了中、高碳合金钢工件表面修复的高强、高韧新型堆焊焊条。

The high strength and high toughness hardfacing covered electrode to the medium-high carbon alloy steel surface" repair was put forward in this paper.

4. 结果表明,碳显著的影响低碳高合金钢的组织和性能,而以锰代镍低碳高合金钢可以获得预期的组织与性能。

The results indicate that carbon influences structure and properties of LCHA significantly, and substitution for nickel with manganese may result in expected structure and properties.

5. 文章最后还对以锰代镍低碳高合金钢的冲击腐蚀磨损机制进行了探讨。

At last, this article also discussed the mechanisms of corrosive impact abrasion for these LCHA after substitution for nickel with manganese.

6. 结果表明,以锰代镍低碳高合金钢可以获得预期的组织与性能。

The results indicate that LCHA with Mn in place of Ni could gain the anticipated structure and performance.

7. 本文介绍采用高碳中铬合金钢作为磨机衬板材料,按照正交设计法优选热处理工艺参数,得到材料韧性和硬度的理想配合。

The mill Liners of high-carbon medium-chromium alloy steel have ideal coordination of toughness and hardness after optimum heat treatment determined by cross-design.

8. 单孔式回油,模具采用高碳钨合金钢不易破损。

Punch dies made of high carbon tungsten steel and not easy to wear off.

9. 结果表明,2.0J冲击功条件下,中碳合金钢、低碳高合金钢均以浅层剥落为主,抗冲击腐蚀磨损性能相近;

Results show that the leading mechanisms of both alloys are shallow flaking under 2.0 J impact work, and the anti-impact-corrosion wear are close.

10. 该方程不仅适合微合金中碳钢的铁素体和珠光体组织,而且也适合高碳微合金钢的珠光体组织和低碳微合金钢的铁素体组织。

The equations suit not only ferrite and pearlite in microalloyed medium carbon steel but also pearlite in high carbon microalloyed steel and ferrite in low carbon microalloyed steel.

11. 介绍了应用DV - 4光电光谱仪,仅用一种测定条件,测定高合金钢中碳、硫、磷、锰、硅、铬、镍、钼、钒、钨、钛、铌、铝元素的含量的方法。

The method of measuring c, s, p, Mn, Si, Cr, Ni, Mo, V, W, ti, Nb, Al element content by DV-4 photoelectric spectroscope on one condition is introduced.

12. 比较两种材料试样在一定时间内的失重变化情况,表明低碳高合金钢的抗冲击腐蚀磨损性能优于高锰钢。

Wear loss of specimens for these two steels during a certain time show that low carbon high alloy steel is much more resistant to corrosive impact abrasion than high manganese steel.

13. 针对这一情况,提出了采用高碳锰合金钢锤头、低合金钢锤头及复合锤头。

Aimming at this situation, it introduces applying hammers of alloy steel with high carbon and manganese content and low alloy steel and composite hammers.

14. 结果表明,在相同试验条件下低碳高合金钢的冲击腐蚀磨损性能要优于高锰钢的。

The results show that the resistance of low carbon high alloy steel is better than that of the high manganese steel under the same test condition.

15. 在改进的MLD - 10型冲击腐蚀磨损试验机上,选择三种不同的冲击功,对以锰代镍的低碳高合金钢的冲击腐蚀磨损性能进行了测试。wwW.wEnTIYI.com

Under three different impact energy, LCHA with Mn in place of Ni were tested with a modified MLD-10 wear tester to investigate their behavior of corrosive impact abrasion.

16. 在改进的MLD - 10型冲击腐蚀磨损试验机上,对不同成分的低碳高合金钢的冲击腐蚀磨损性能进行了测试。

LCHA with several variations of composition were tested with a modified MLD-10 wear tester to investigate their behavior under corrosive impact abrasion.

17. 结果表明:加镍低碳高合金钢无论退火态还是淬火回火态,其组织均为单相板条马氏体;

The results show that as-annealed microstructure and as-quenched-tempered microstructure of the low carbon high alloy steel added nickel are both single-phase lath martensite.

18. 结果表明:加镍低碳高合金钢无论退火态还是淬火回火态,其组织均为单相板条马氏体;

The results show that as-annealed microstructure and as-quenched-tempered microstructure of the low carbon high alloy steel added nickel are both single-phase lath martensite.

版权声明:问题易所有作品(图文、音视频)均来源网络,版权归原创作者所有,与本站立场无关,如不慎侵犯了你的权益,请联系我们告知,我们将做删除处理!