
词语导航
基本信息
词语:微型计算机程序
繁体:微型計算機程序
拼音:wēi xíng jì suàn jī chéng xù
英语翻译
【计】 microcomputer loader
分词翻译
微型的英语翻译:
miniature; minitype
【计】 minisize
【化】 miniature; minitype
计算机程序的英语翻译:
【计】 computer program
翻译例句
1. Forth是个互动编程环境针对在迷你和微型计算机上开发程序而设计。
Forth is an interactive programming environment originally designed for programmers developing applications using mini - and micro-computers.
2. 在具有微程序控制的指令集的微型计算机中,它包含另外的控制存储单元。
In a microcomputer with a microprogrammed instruction set, it contains an additional control-memory unit.
3. 本文使用PB- 700微型计算机和通用的BASIC语言编制了摄谱法光谱分析数据处理程序。
In this paper, an utility program has been worked out for spectrographic analysis based on PB-700 microcomputer and common BASIC language.
4. 程序在PANDA- 100型微型计算机上运行,取得了满意的结果。
This program has been run on PANDA-100 microcomputer and achieved satisfactory results.
5. 用BASIC语言编制了程序,在微型计算机上实现。
A program is made in BASIC language and carried out on a microcomputer.
6. 你的微型计算机执行程序的速度将与你的时钟信号的速度成线性关系。
The speed with which your microcomputer executes programs will vary linearly with the speed of your clock signal.
7. 有语言实验室,有带游戏和其它为语言学习的程序的微型计算机。
There"s a language laboratory; there are microcomputers with games and other programs designed for language learning.
8. 本文介绍了一种适应于PC- 1500微型计算机的边坡稳定性分析程序。
This paper describes a PC-1500 microcomputer program for stability analysis of rock slopes.
9. 控制技术工作者可借鉴此方法,在微型计算机上,建立各种分析程序。
Using this method, a control engineer can develop all kinds of simulation program on the microcomputer.
10. 对柔性吊桥的的常用活载,编成程序中微型计算机上约10分钟可求解,适于设计人员使用。
With a program suitable for designers to calculate cables of flexible suspension Bridges under ordinary live lods. problems can be solved on personal computers in about 10 minutes.
11. 本文描述的信息分布处理系统,主要由大量单片微型计算机(MC)及一总管程序构成。
This paper describes a distributed information processing system consisting mainly of a large number of single-chip micro-computers(MC)and a general control program.
12. 针对具有控制功能的一种BASIC语言,在使用汇编语言的同时,也给出了使用TRS—80微型计算机的BASIC 控制程序。
While expounding the assembly source program, this paper also presents a TRS - 80 BASIC program which is known to possess a control function, too.
13. 采用FORTRAN语言编出了用伴随网络法计算网络直流灵敏度的程序,并用此程序在M 68000微型计算机上计算两实例。
A program written in FORTRAN for calculating sensitivity of d. c. network by adjoint network method is given and two examples are demonstrated on computer M68000.
14. 本文着重介绍微型计算机控制的保暖性测试仪硬件软件设计的主要电路和程序流程图,并阐述设计的原理与恃点。
The major circuits and flow-charts of hardware and software design for micro-computer controlled heat insulation tester are presented and the designing principles and features described.
15. 本文简述了用微型计算机编印《时间公报》的BASIC程序设计方法。
This paper presents a brief description about the method of BASIC program design in compiling "Time Bulletin".
16. 本专家系统的外壳程序是用BASIC语言写成,它可在IBMPC微型计算机及其兼容机上运行。wWW.wenTiyi.CoM
The shell program for the LCB expert system is written in BASIC and runs on IBM PC microcomputer and 100% compatible machines.
17. 本文给出了微型计算机辅助设计随动系统程序以及多采样自适应的伺服系统仿真程序,并分析了伺服系统的实验结果。
This paper gives a CAD program for servo system and another program for simulation of a multirate servo system and an adaptive servo system. Results of experiments are discussed.
18. 在微机应用中缺乏必需的开发工具是经常会遇到的情况,本文介绍了利用一般的微型计算机来研制微机应用程序的方法,讨论了有关的硬件和软件问题。
Microprocessor application development based upon an existing microcomputer can be effective and very economic. This paper takes hardware and software into consideration in implementing such a system.
19. 可以处理各种复杂形状的剖面线图形,而且具有程序简单、使用方便、速度快、通用性强、便于扩充应用等优点,适合于在微型计算机上开发CAD系统应用。
This algorithm can handle all kinds of complex sectional drawing and has many advantages. For example, its program is simple, rapid and fits microcomputer CAD system well etc.
20. 这个端口通过一个微型计算机或任何其他的可编程序的装置可以控制TH7195。
This port is provided to control the TH7195 by a micro-computer or any other programmable device.
21. 本文以三相桥式晶闸管整流电路为例,讨论波形分析法的原理、采样电路与微型计算机接口电路的设计及应用程序的设计。
As an example, the principle of waveform analysis, the design of sampling circuit, interface and applied programs for 3-phase bridge rectifier are discussed.
22. 介绍了计算机的程序编制,整个计算可由微型计算机来完成。
The computer programming is presented. The entire calculation can be accomplished on a microcompu…
23. 介绍了计算机的程序编制,整个计算可由微型计算机来完成。
The computer programming is presented. The entire calculation can be accomplished on...
24. 介绍了计算机的程序编制,整个计算可由微型计算机来完成。
The computer programming is presented. The entire calculation can be accomplish...
25. 介绍了计算机的程序编制,整个计算可由微型计算机来完成。
The computer programming is presented. The entire calculation can be accomplish...
版权声明:问题易所有作品(图文、音视频)均来源网络,版权归原创作者所有,与本站立场无关,如不慎侵犯了你的权益,请联系我们告知,我们将做删除处理!
