词语导航
基本信息
词语：凸模的
繁体：凸模的
拼音：tū mó de
英语翻译
【计】 diebold
分词翻译
凸的英语翻译：
protruding
【医】 convexity; cyrto-; prominence; prominentia
模的英语翻译：
model; module; mould; pattern
【计】 M; MOD; modulo
【化】 mould
【医】 die; mol; mole
翻译例句
1. 列出了高耐用度凸模的主要类型及其采用的条件。
Basic types of high endurance punches along with the conditions are presented.
2. 分析了冷挤压活塞销凸模的受力情况和主要失效形式。
The stress and the main failure form of the cold extruding die for the piston pins were analyzed.
3. 因受零件自身尺寸的限制，极大影响了凸模的强度和刚度。
It is restricted by limit of punching part, the strength and rigidity of punch is affected significantly.
4. 固定在工作台上的滑道与滑槽可使活动凸模的运动保持较高精度。
The slideway and chute fixed on the workbench may keep a high precision for the motions of the active force plug.
5. 按照这些原则与方法确定分段切除顺序时可提高凸模的抗折断能力。
The subsection excision sequence determined according to these principles and methods can improve the punch"s resistance to fracture.
6. 介绍了铝合金茶壶橡胶胀形模具结构，阐明了聚氨酯橡胶制作凸模的优点。
The structure of rubber bulging die for the aluminium alloy teapot is introduced. The advantage of the manufacturing punch with the polyurethane rubber is expounded.
7. 对于凸缘部位的浅拉深，采用压边圈兼作浅拉深凸模的作用，取得较好的效果。
To low drawing in flange part, the blank holder can be used as punch, and the effect is good.
8. 有时候用摇摆凸模结构来代替滑块结构，本文主要介绍了摇摆凸模的设计制造。
In this paper, mainly introduced the design and manufacturing of the swingwing punch.
9. 以玻璃制件的热成形凸模为例，说明热成形凸模的主要缺陷：凸模裂纹和凸模伤。
Taken the hot-forming punch of a glass part as an example, the main defects of hot- forming punch is explained, including punch crack and punch wound.
10. 不但使用户大幅度降低了凸模的购置成本，而且使凸模的使用寿命得到成倍的提高。
Thus not only the purchase cost was reduced, but also the working life of the protruding die was prolonged.
11. 明确指出妨碍活塞销冷挤压技术在国内推广应用的关键因素是其冷挤压凸模的寿命太短。
It is pointed that application and dissemination"s key factor of piston pin"s cold extruding technique in China is that working life of piston pin"s cold extruding punch is too low.
12. 应用成组技术对冷冲模凸模的特征进行了分析，采用特征代码设计了其零件分类编码系统。
The feature of convex-die is analysis by GT technology, and it"s classification and coding system is designed by using characteristic code in this article.
13. 介绍了光盘注射模冷却系统的设计方法，以及动镜面、定镜面、浇口与凸模的冷却水路等。
The design manner of cooling system of CD injection mold was mainly introduced, and the cooling water channel of moving plate, stationary plate, sprue and punch etc were detailed.
14. 分析了挤压翻边与传统翻边应力状态的不同之处，以及翻边凸模的冲头曲率半径对翻边效果的影响。
The differences of stress state between extrusion-flanging and traditional flanging, and the influences of curvature radius of burring punch on flange height were analyzed.
15. 本文主要利用FEA及PVD技术，针对细小凸模的断裂和磨损两种失效形式，进行失效分析与优化。
In this paper, the failure of pin punch was analyzed and optimized based on FEA and PVD, according to failure mechanism of fracture and wear of pin punch.
16. 对小孔凸模失效形式进行了分析，提出了几种较为理想的预防措施，以提高小孔凸模的使用寿命和冲压件质量。
Give some analyses to the failure forms of pinhole punch, bring forward several more ideal prevention measures, in order to improve usage life of a pinhole punch and quality of punching part.
17. 针对该冲压件弯曲成形难的问题，设计了双凸模弯曲模，通过双凸模的依次动作可一次成形该零件的复杂形状。
Aimed at the difficulties in the bending forming of punching parts, the bending die with dual-punch is designed, the complex shape of this part is once formed by the ordinal action of dual-punch.
18. 介绍了挤压型材模具中，具有阶梯式凸模的分流组合模设计的方法和设计要点，用实例阐述了该类型模具的设计过程和设计思路。
Introduced design method and points of separation combined extruding die with ladder-shape punch in extruding die, stated extruding die design process and thought using practical example.
19. 固体颗粒介质成形新工艺，是采用固体颗粒代替刚性凸模(或弹性体、液体)的作用，对金属板料成形的工艺。
Solid granules medium forming new technology (SGMF) is a technology which USES solid granules medium instead of rigid punch (or elastomer, liquid) to achieve the sheet forming.
20. 素压浮凸：泛指用不着墨的电或模在纸品上压成凸纹效果的方法。
Blind embossing: a general term FOR the process of raising an image using an un-inked block or die on paper or board.
21. 介绍了固体颗粒介质成形新工艺，即采用固体颗粒介质代替刚性凸模(或弹性体、液体)的作用对板料进行软模成形的工艺，并阐述了新工艺的优点。
Solid granules medium forming technology is an advanced soft-tool forming technology which USES solid granules medium instead of rigid punch (or elastomer, liquid) to form sheet.
22. 根据具体情况随时可以快速调换相应的凸模和圆凹模，及转盘的快速定位，类似于数控转塔冲床，来达到加工产品多品种的要求。
We could quickly change punch and round concave at anytime production required, the quick location of turntable like nc revolving tower type press machine, it could produce many kinds of productions.
23. 在用半球形凸模进行试验时发现，所用凸模直径和试件形状的不同对FLD有影响。
An experiment with hemispheric punches reveals that the difference in their diameters and the specimen shape has some influence on FLD.
24. 优化了模具结构，同时也介绍了在冲压过程中凸、凹模易开裂采取的措施和方法。
Also introduced the measure of prevent the convex and concave die cracking in course of pressing.
25. 冲孔凸模磨损是模具失效的主要形式之一。
The wear of piercing punch is one of main die lose efficacy.
26. 介绍了多工位数控冲床用百页窗模具的设计，重点介绍了下装凸模、上装镶拼凹模及卸料板的设计和计算方法。WWw.weNtIYi.Com
This article introduces the design of louver tooling for turret punch press, mainly focusing on the design and calculation of die, punch body and stripper plate.
27. 介绍了利用浮动凸模来提高零件拉伸成形性能的方法。
The article introduces a method to improve the forming property with floating punch.
28. 以聚氨酯橡胶代替通常钢模中的凹模或凸模是比较有效的方法之一。
It"s one of best methods to use polyurethane rubber rather than usual cavity or core in steel die.
29. 针对板料成形回弹精度问题的数值模拟，从理论上分析了凸模虚拟速度和板料虚拟密度对薄板变形能的影响。
For the simulation accuracy of springback problem in sheet metal forming, the effect of punch virtual velocity and sheet virtual density on the sheet strain energy was studied in this paper.
30. 针对板料成形回弹精度问题的数值模拟，从理论上分析了凸模虚拟速度和板料虚拟密度对薄板变形能的影响。
For the simulation accuracy of springback problem in sheet metal forming, the effect of punch virtual velocity and sheet virtual density on the sheet strain energy was studied in this paper.
版权声明：问题易所有作品（图文、音视频）均来源网络，版权归原创作者所有，与本站立场无关，如不慎侵犯了你的权益，请联系我们告知，我们将做删除处理！