词语导航
基本信息
词语：槽缝
繁体：槽縫
拼音：cáo féng
英语翻译
【化】 groove joint
分词翻译
槽的英语翻译：
chamfer; gutter【计】 slot
【化】 channel
【医】 alvei; alveus; crib; gutter; slot; socket; tank; trough
缝的英语翻译：
seam; sew; slot; stitch【化】 opening
【医】 crevice; nesis; raphe; rhaphe; seam; sutura; suturae; suturation
suture; suture joints; suturing
翻译例句
1. 与普通贴片相比，加载槽缝后贴片面积减小了近50%。
By loading slots on the patch, nearly 50% area is reduced compared with conventional patch.
2. 将矩量法与迭代物理光学法结合解决带有槽缝结构的二维电大尺寸目标的电磁散射问题，并将解决的问题范围拓展到三维电大尺寸金属目标的情况，为混合方法的研究提供了一定的参考依据。
Finally the scattering problems of complex-shaped electrically-large 2d PEC targets are solved based on the hybrid method of IPO and MoM, which can be easily expanded to the 3-d condition.
3. 本文通过对裂缝修补机理和修补时机的分析，得出了裂缝修补时对裂缝的开槽槽壁和灌缝材料的要求以及最佳的灌缝时间。
According to analyze cracks repair mechanism and repair time, obtain the request of the cracks slot wall and patching material when crack patching and the best patching time.
4. 您把它投入旋转栅门的缝槽里，然后推动旋转栅门就可以进入站台了。。
You put it in the slot at the turnstile and then push the turnstile to get into the platform.
5. 清洁活塞环槽或油环开缝，绝对不能损伤金属部分。
Be sure that you do not remove metal when cleaning ring grooves or oil slots.
6. 该叉排离散缝槽结构应用于发动机进气道的导流叶片上。
The structure of disorder discrete slots will be applied to the guide vane of the engine practically.
7. 已有工程实践表明，趾板不分缝，采取预留宽槽跳仓浇注可能是解决趾板裂缝的有效途径。
It is shown by engineering practice that if the plinth is not partitioned by slits the problem may be solved by wide trough left in advance.
8. 阀缝硅藻阀上的中槽。
The median groove of a diatom valve.
9. 通过对标准门槽及窄缝门槽的体型研究，分别拟定了适合各自门槽的闸门底缘型式。
Finally, through the study of structural forms of standard gate slot and narrow slit gate slot, the appropriate gate bottom rim patterns are recommended for each type g.
10. 采用窄缝槽物理模型来模拟地下水运动，具有形象、直观的优点。
The physical model of narrow slit has been adopted to simulate groundwater movement and it has many excellences in visualization and intuition.
11. 最后提出了管材激光割缝时槽宽尺寸精度控制的补偿原则。
At last, the authors give a compensation principle for dimensional accuracy control of grooving kerf width with laser beam for seamless pipe.
12. 这些元素可以以不同方式组合在一起，例如：一个搭接接头可能用角接、塞焊和缝焊固定，一个丁字接头可以用一个搭接或槽焊来完成。
The elements can be put together in various ways. For example, a lap join may be held by a fillet, plug, or slot weld, and and a tee joint by a fillet or groove weld.
13. 通过对标准门槽及窄缝门槽的体型研究，分别拟定了适合各自门槽的闸门底缘型式。
Finally, through the study of structural forms of standard gate slot and narrow slit gate slot, the appropriate gate bottom rim patterns are recommended for each type gate slot, respectively.WWW.WEnTiYi.COM
14. 您把它投入旋转栅门的缝槽里，然后推动旋转栅门就可以进入站台了。
You put it in the slot at the turnstile and then push the turnstile to get into the platform.
15. 结果表明，钢体上开工艺槽导致焊后残余应力增加，对接头强度不利；钎缝厚度存在一最佳值。
The result showed that notch was disadvantageous to the strength of joints, and the optimal value of filler metal thickness existed.
16. 模具采用燕尾槽齐缝设计可方便更换不同尺寸。
Mold Design using dovetail joints together of different sizes can be easily replaced.
17. 通过对标准门槽及窄缝门槽的体型研究，分别拟定了适合各自门槽的闸门底缘型式。
Finally, through the study of structural forms of standard gate slot and narrow slit gate slot, the appropriate gate bot...
18. 由于激光对划槽材料几乎不产生机械冲力和压力，加上激光光斑小、划缝窄。
Because the laser process has no machine momentum and pressure, and has a small facula and a narrow slot material.
19. 钢梭型伸缩缝系统按照平面图对道路表面、路槽及路缘进行密封，防止水渗流通过缝隙区域。
The Steel Finger type expansion joint system shall seal the deck surface, gutters and curbs in accordance with the plans and prevent water from seeping through the joint area.
20. 通过对标准门槽及窄缝门槽的体型研究，分别拟定了适合各自门槽的闸门底缘型式。
Finally, through the study of structural forms of standard gate slot and narrow slit gate slot, the appropriate gate bottom rim patterns are recommended for each type g...
21. 本文采用两相流模型对开双抽缝除湿槽的某末级中空静叶片进行了数值模拟研究研究。
The structure of double moisture removal suction slot in a final stage hollow vane was investigated using two-phase numerical simulation methods.
22. 本文采用两相流模型对开双抽缝除湿槽的某末级中空静叶片进行了数值模拟研究研究。
The structure of double moisture removal suction slot in a final stage hollow vane was investigated using two-phase numerical simulation methods.
版权声明：问题易所有作品（图文、音视频）均来源网络，版权归原创作者所有，与本站立场无关，如不慎侵犯了你的权益，请联系我们告知，我们将做删除处理！