弧接触用英语怎么说,弧接触的英文翻译


词语导航

基本信息

词语:弧接触

繁体:弧接觸

拼音:hú jiē chù

英语翻译

【电】 arcing contacts

分词翻译

弧的英语翻译:

arc
【化】 arc
【医】 arc

接触的英语翻译:

contact; contiguity; get in touch with; meet; osculate; osculation; tangency
touch
【医】 c.; contact; contiguity; hapt-; hapto-; per contiguum; taction; tactus
touch

翻译例句

1. 对于配数控用,应选择非接触起弧方式。

To match with numerical control, should choose the contact arcs way.

2. 采用热电偶夹丝法测量了平面磨削山西黑石材过程中接触弧区的温度。

Temperature response at contact zone during grinding of granite were measured using thermocouple detector.

3. 试验模拟了切削面积、接触弧长、切削面形状、切削齿后倾角和岩石性能对PDC切削齿破岩受力的影响。WwW.WeNTiYi.Com

The effects of cutting area, contact arc length, the geometry of cutting face, back dip angle of PDC cutter and rock performance on force of PDC cutter breaking rock were simulated experimentally.

4. 应用弹性力学理论,推导出接触点的曲率半径,对三弧段等距型面联接进行接触应力计算。

The curvature radius was derivated and the contact stress of the three-arc-sect isometric type surface was calculated through the elastic dynamics theory.

5. 分析认为,锯切方向直接影响着管壁的受力状态,锯片与管子的接触弧长和锯切圆周力成正比关系。

The saw cutting direction directly affects the pressed wall thickness, the contacting arc length between saw disc and pipe has direct ratio to the cutting circumference force through analysis.

6. 弧刷的接触阻抗会产生问题(局部温升,噪声偏移等等)。

The resistance of the wiper contact will cause problems local heating, noise offsets etc.

7. 由局部综合法,利用二阶接触参数的可预控性,从而优化弧齿锥齿轮的啮合性能。

Based on the local synthesis method, the meshing behavior is optimized with the help of controllability of the second order contact parameters.

8. 介绍了一种新型的智能混合式无弧交流接触器。

A new type of intelligent hybrid arcless AC contactor was introduced.

9. 将该衣架主体往上提升,两长支杆的交叉接点与晒衣杆接触,两长支杆上部弧弯即 分开。

The cross contact of the two long supported bars contacts with a clothes bar through lifting the clothes rack main body, and the upper arc-shaped bending of the two long supported bars are separated.

10. 本文提出了一种非接触超声传感埋弧焊焊缝跟踪系统。

A new kind of the seam tracking system with non-contact ultrasonic sensor in SAW is presented in this paper.

11. 一般电流大于100a的等离子电源,都是非接触起弧方式。

General current more than 100 a plasma power, are not contact arcs way.

12. 电弧弧根不应接触绝缘子表面,但允许电弧通道的中间部分可以擦过绝缘子。

The roots of the arc must not be allowed to come into contact with insulator surface, whereas the middle of the arc channel can do so.

13. 首次采用线图法分析了其啮合过程,建立了双圆弧齿廓弧齿锥齿轮重合度、多点接触系数和多对齿接触系数计算方法;

The meshing process is analyzed using line graph method firstly, calculation methods of the contact ration, multi-point contact coefficient and multi-pair contact coefficient are established;

14. 首次采用线图法分析了其啮合过程,建立了双圆弧齿廓弧齿锥齿轮重合度、多点接触系数和多对齿接触系数计算方法;

The meshing process is analyzed using line graph method firstly, calculation methods of the contact ration, multi-point contact coefficient and multi-pair contact coefficient are established;

版权声明:问题易所有作品(图文、音视频)均来源网络,版权归原创作者所有,与本站立场无关,如不慎侵犯了你的权益,请联系我们告知,我们将做删除处理!