曲轴轴承用英语怎么说,曲轴轴承的英文翻译


词语导航

基本信息

词语:曲轴轴承

繁体:曲軸軸承

拼音:qū zhóu zhóu chéng

英语翻译

【建】 crank shaft bearing

分词翻译

曲轴的英语翻译:

【化】 bent axle; crank shaft

轴承的英语翻译:

bearing
【化】 bearing

翻译例句

1. 曲轴轴承为双列球面滚柱轴承。

Crankshaft bearings are double-row spherical roller bearings.

2. 传感器最佳位置是在曲轴轴承正对的发动机两侧或油底壳处。

The optimal positions of the vibration sensor should be located on both sides of the crank-shaft bearing or bottom of the engine.

3. 同样,在进行曲轴轴颈和曲轴轴承配合间隙的测量时,也可以借鉴这种操作技巧。

Similarly, in the crankshaft journal and crankshaft bearing clearance measurements, they can draw on such skills.

4. 本文讨论了内燃机曲轴轴承副的工作状况和磨损,给出曲轴轴颈磨损的计算模型和计算方法。

The operation conditions and wear of crankshaft bearings in internal combustion engine are discussed in this paper. A model and method for calculating the crankshaft journal wear are given.

5. 内燃机曲轴轴承所受到的冲击信号是非平稳、时变信号,用传统的诊断方法难以进行故障的早期发现和诊断。

Vibration signals borne by different main bearing clearances are not stationary and time variant. It is difficult to early detect and diagnose by means of traditional methods.

6. 半精加工的主轴承安装后需要修整和调配,这样曲轴就必须拆下。

Semifinished main bearings require finishing and fitting after installation, so that the crankshaft must be taken out.

7. 曲轴有三个主要轴承期刊。

The crankshaft has three main bearing journals.

8. 第二图为曲轴中心轴承持有人安装在该区块。

The second photo shows the crankshaft center bearing holder installed in the block.

9. 该系统可测量内燃机主轴承的油膜厚度、油膜温度、曲轴转角、转速、轴心轨迹和最小油膜厚度。

It can measure the oil film thickness, oil temperature, crank Angle, speed, journal center locus and minimum oil film thickness of main bearing in diesel engine.WwW.weNTIyi.Com

10. 曲轴在发动机曲轴箱带动轴承旋转,但是轴承的数量通常由发动机内气缸的数量和发动机的设计来决定。

The crankshaft revolves in bearings located in the engine crankcase, but the number of bearings used usually depends on the number of cylinders in the engine, and the design of the engine.

11. 发动机关键工位螺栓包括连杆螺栓、曲轴螺栓、主轴承盖螺栓、气缸盖螺栓、飞轮螺栓和减振器螺栓等均属螺纹联接。

The key position bolt of the engine include connecting rod, crankshaft, main bearing, cylinder head, flywheel and shock absorber bolt, all of which belong to bolt fastening.

12. 通过对发动机曲轴轴颈与轴承损坏原因的分析,重点阐述了发动机在使用与维修中预防损坏的措施和方法。

By analyzing reasons for break of engine crankshaft journal and bearing, this paper describes mainly some countermeasures they are break in use and maintenance.

13. 本节介绍曲轴、主轴承、发动机机体和气缸的维修。

This section describes the servicing of crankshafts, main bearings, and engine Blocks and cylinders.

14. 对主机曲轴红套滑移,并使二道主轴承严重损坏的机损事故进行了分析。

An engine accident by slipping of shrink fit crankshaft which caused severe damage of two main bearings is analyzed.

15. 曲轴主轴承进入口。

The feed holes for the crankshaft main bearings.

16. 轴承负荷及曲轴疲劳强度的计算均按简支梁进行。

The bearing loads and crankshaft fatigue strength are calculated according to the principle of a simple beam.

17. 在此基础上,进行了内燃机曲轴—轴承系统摩擦学、刚度和强度的耦合研究。

Then, the coupling of tribology, stiffness and strength of crankshaft-bearing system for internal combustion engine is studied.

18. 曲轴上的导向轴承:曲轴上的导向轴承一般或者是轴瓦,或者是球轴承。

Pilot bearing in crankshaft. The pilot bearing in the crankshaft is usually either a Bushing or a Ball bearing.

19. 在图1-4中,曲轴实际上由以下不同的部分组成,它们分别是:主轴承轴颈、连杆轴颈、曲轴臂、轴承、平衡配量(?)以及飞轮端。

The crankshafts shown in Fig 1-4 is actually made up of various parts such as main bearing journals, rod journal, crank arm, bearing, counter balanced weight and flywheel end.

20. 采用细曲轴及平面滚动轴承技术及较低粘度的冷冻油以提高机械效率。

Applying the slender crankshaft, the level rolling bearing technology, and lower viscosity refrigeration oil, increased the mechanical efficiency.

21. 曲轴上平衡重的安装减小了曲轴所受的弯矩,但也影响了主轴承载荷的大小和分布。

The counterweight is installed on the crankshaft for reducing the bending moment on it, but it will influence the magnitude and distribution of the main bearing load.

22. 曲轴穿过侧板、隔板及两个压缩缸,并由两个侧板内的轴承支撑。

The crankshaft passes through the lateral plate, the separator plate and the two compression cylinders, and is supported by a bearing between the two lateral plates.

23. 提出用剖分结构的静压轴承作为氧气压缩机曲轴支承轴承,取代轴瓦剖分形式的滑动轴承。

The idea of using split hydrostatic bearing as the support bearing of crankshaft in oxygen compressor to replace the split sliding bearing was proposed.

24. 同时得出曲轴各个轴承曲拐的应力应变状态,并分析了曲轴在不同工况下的受力情况。

Meanwhile get the state of the stress and deformation of every crankshaft, analyze the case of the stress of crankshaft under different work condition.

25. 曲轴的各轴颈在很高的比压下作高速旋转运动,使轴颈和轴承受到强烈磨擦。

Because the shaft necks whirligig with high speed under high pressure, the shaft necks and bearings endure intense attrition.

26. 半精加工的主轴承安装后需要修整和调配,这样曲轴就必须拆下。

Sparated Bearing block for main transmission shaft Easy for maintenance and fix.

27. 类似的轴承,主轴承,是用来安装曲轴的块。

Similar bearings, called main bearings, are used to mount the crankshaft in the block.

28. 这是标准的,在几乎所有类型的发动机,这使曲轴箱之间的球轴承更激烈。

It is standard in almost all types of engines and it makes the crankcase between the ball bearings more stiff.

29. 这是标准的,在几乎所有类型的发动机,这使曲轴箱之间的球轴承更激烈。

It is standard in almost all types of engines and it makes the crankcase between the ball bearings more stiff.

版权声明:问题易所有作品(图文、音视频)均来源网络,版权归原创作者所有,与本站立场无关,如不慎侵犯了你的权益,请联系我们告知,我们将做删除处理!