内压试验用英语怎么说，内压试验的英文翻译

词语导航

基本信息

词语：内压试验

繁体：內壓試驗

拼音：nèi yā shì yàn

英语翻译

【化】 internal pressure test

分词翻译

内压的英语翻译：

【化】 internal pressure; intrinsic pressure

试验的英语翻译：

experiment; test; try; try on; try out; examination; experimentation; trial
trial run
【计】 breadboarding
【医】 probation; test; tria
【经】 test; trialWww.WentiYi.Com

翻译例句

1. 对间断焊焊接接头的金相分析表明其金相组织正常，内压试验结果表明该结构能安全运行。

The metallographic analysis shows that the metallurgical structure is proper. The results of internal pressure test indicate that the hot tap structure can work safely.

2. 本文基于脉动内压疲劳试验结果，对厚壁圆筒构件的动态自增强原理进行了分析研究。

Based on the results obtained from fatigue tests under pulsating internal pressure, the mechanism of dynamic autofrettage of thick wall-cylinder components is studied in this paper.

3. 本文通过试验研究提出了在碱性压热氧化条件下，金精矿在高压釜内进行闪速氰化的新工艺。

The gold concentrates are pretreated by alkaline hot-press oxidation followed by flash cyanidation in autoclave.

4. 提出了估算开孔结构风致内压脉动的频域分析方法，并实施了风洞试验进行验证。

A method for estimating wind-induced fluctuating internal pressure in the frequency domain is proposed and wind tunnel tests were carried out to verify the method.

5. 通过理论分析与风洞试验研究背景孔隙对开孔结构风致内压响应的影响。

Theoretical analysis and wind tunnel tests were carried out to study the influence of background porosity on wind-induced internal pressure response for structures with openings.

6. 基于钢制内压容器静强度在最苛刻压力试验条件下的可靠度分析，建立了统一确定钢制压力容器试验压力的模糊可靠性理论。

Based on the reliability analysis of steel pressure vessels under the harshest condition, the fuzzy reliability theory of determining the testing pressure of steel pressure vessels is established.

7. 本文从ANSYS有限元分析和试验两方面分别对光管和波节管在承受内压爆破和承受外压失稳时的性能进行研究。

This paper studies the performance of internal pressure blasting and external pressure squirm between smooth tube and corrugated tubes from the ANSYS finite element analysis and testing.

8. 本文采用刚性模型风洞试验研究开孔结构风致内压特性。

Wind tunnel tests of rigid structural model are carried out to investigate the internal pressure of structures with openings.

9. 某高膛压火炮试验中发现多点点火方案的装药利用率较高，但膛内压力波较大。

The charge utilization ratio is high for multi-point ignition tube experiments in a high-pressure gun, but the chamber pressure wave is high.

10. 通过三类弯管形式压损试验，发现了短半径弯头在一个较大料气输送比范围内均产生最小压损；

By means of the pressure loss in three kinds of bend configuration. it is found out that the short radius elbows appear to yield the lowest pressure loss in a wide range of mass over air ratio.

11. 文中同时分析了压力及内压与压缩位移一齐作用时的平面稳定性试验结果。

The result of test of plane stability is analyzed as well when the expansion joint bellows are subjected to internal pressure and internal pressure together with compression deformation.

12. 系统内配置高，低压注水泵供压装置，试验介质循环贮存使用。

Equip with the high and low pressure water pump pressure supply device in system, the test medium circulating storage use.

13. 然后考察不同结构的模型在考虑温度场履历情况下加载均匀内压的计算结果，计算表明其计算爆破压力与试验爆破压力基本一致。

And then the conditions of different models under the pressure load considering temperature history are researched. The results showed that calculated burst pressure accords with test result.

14. 系统内配置高，低压水泵供压装置，试验介质循环贮存使用。

High disposition built-in system, low pressure water pump device, test medium circulation storage use.

15. 应用可靠性设计方法，对压力试验时钢制薄壁内压圆筒形容器初始静强度的最小可靠度进行了定量分析。

By using reliability design methods, minimal reliability of virgin static strength of steel thin wall cylinder during pressure test is quantitative analyzed.

16. 为了分析齿轮参数对杯形薄壁内齿旋压成形的影响，本文采用工艺试验的方法，对梯形内花键和渐开线内齿轮旋压成形进行了研究。

Analysis of gear parameters on impact of cup shaped thin wall inner gear spin forming, and the spinning process for the two types of inner gears were discussed based on the experimental investigation.

17. 应用可靠性设计方法，对压力试验时钢制薄壁内压圆筒形容器初始静强度的最小可靠度进行了定量分析。

By using reliability design method, the reliability range of virgin static strength of spherical vessel was quantitatively analyzed under the most severe pneumatic and hydraulic test conditions.

18. 通过研究中密砂三轴压缩的试验曲线，发现其应力–应变关系曲线在常规围压范围内具有归一化特性。

Study shows that there is normalization characteristic about the stress-strain curves of mediate-dense sands in the range of routine confining pressure.

19. 从控制薄壁内压容器在不同工况下最小初始可靠度的角度，对其试验压力系数进行了探索。

An approach was made of the test pressure coefficient based on the requirement of controlling the minimal virgin reliability of the thin wall internal pressure...

20. 仿真与试验分析表明，内压加载和轴向进给匹配关系的优劣是零件液压成型的关键；

The simulation and test analysis show that advantages and disadvantages of the matching correlation between internal pressure loading and axial feeding is critical in components hydroforming;

21. 并用压坯单重递减法试验证实，当将压模收缩比增加到1 2 2以上时，可以保证压坯内孔不出现裂纹。

The test of single compact weight decrease proved that when the shrinkage ratio of the compacting die is increased to over 1.22, there is no more crack initiated in the compact inner hole.

22. 并用压坯单重递减法试验证实，当将压模收缩比增加到1 2 2以上时，可以保证压坯内孔不出现裂纹。

The test of single compact weight decrease proved that when the shrinkage ratio of the compacting die is increased to over 1.22, there is no more crack initiated in the compact inner hole.