泵的出口用英语怎么说，泵的出口的英文翻译

词语导航

基本信息

词语：泵的出口

繁体：泵的出口

拼音：bèng de chū kǒu

英语翻译

【化】 delivery side of pump

分词翻译

泵的英语翻译：

pump
【化】 pump
【医】 pump

出口的英语翻译：

exit; escape; export; issue; outcome; outlet; speak out; vent
【医】 exitus; outlet; portal of exit
【经】 export; exports

翻译例句

1. 从泵的出口，水流通过上游水箱(在轴流式水轮机这边)、模型机、下游水箱返回泵的进口。

Starting from the outlet of the pump, the water runs through the upstream tank (on the Kaplan side), the model, the downstream tank and back to the inlet of the pump.

2. 对泵的出口角进行了改良，恰当的选材，降低了成本，得到了良好的性能，满足实际使用工况条件。

The Angle of the pump had improved, the appropriate selection and lower costs, get a good performance, meet the actual use of working conditions.

3. 高粘度泵的出口管路上还应当设置安全阀等保护装置，这样一旦泵的出口通道发生堵塞，就可以打开安全阀卸压。

High viscosity of the pump outlet pipe also shall set up relief valve or other protective device on the road, so that once the clogging pump export channels, can open the relief valve pressure relief.

4. 用户确认泵出口去丁醇处理装置的最大扬程是合适的。

Ctc maximum head is suitable for pump discharge to butanol handling facility.

5. 螺杆泵是一种容积式回转泵，当出口端受阻以后，压力会逐渐升高，以至于超过预定的压力值。

Screw pump is a kind of rotary pump, when the outlet end is blocked, the pressure will gradually increase, so that more than a predetermined pressure value.

6. 在这种状况下，必须降低泵的转速，加大电机的功率，加大进出口的管径来减少介质的流动阻力。

Under this situation, we must reduce the speed of pump, increase the power of the motor, increase the import and export of pipe diameter to reduce the flow resistance of the medium.

7. 从防喷器组出口到高压钻机泵之间的高压管线。

A high-pressure pipe leading from an outlet on the BOP stack to the high-pressure rig pumps.

8. 本文主要研究混流泵出口环量对泵出水管道水力特性的影响。

The influence of outlet circulation of mixed-flow pump on the hydraulic performance of the outlet pipe was studied in this dissertation.

9. 还给出微泵流量与扩散管长宽比、厚宽比、液体粘度和进出口反压差的定量关系。

Quantitative relations of the pump flow rate versus the ratio of diffuser length to width, the ratio of diffuser thickness to width, fluid viscosity and backpressure were also given.

10. 泵的基本部件如出口段、圆柱管和导流壳组件等可以组装在一起，并根据客户要求很好地满足不同的工况需要。

The basic components of head, column pipe and bowl assembly are combined and customized to perfectly match individual duty needs.

11. 通过对不同出口安放角叶轮的能量平衡试验，了解到出口安放角对泵能量性能的影响。

Effect of blade Angle at exit on energy performances is shown by conducting energy equilibrium test on impellers with different exit blade angles.

12. 对大泵改造保留出口导叶的叶轮改型方案作了深入的探讨。

A reform scheme with exit guide vane remained for large axial flow pumps is discussed deeply.

13. 试验结果表明，改变泵出口管线结构，使泵出口压力在一定范围内工作时，流量变化大，而且泵效率较高，可以作为泵调整参数的一种手段；

The test results have proved that the flow rate widely varied and the pump efficiency is high when the pump outlet line structure was altered and the outlet pressure was controlled in a special limit.

14. 泵体和泵盖构成泵的工作室，泵体的入口为水平方向，出口垂直向上。

The pump body and pump cover composes the pump studio. The inlet of the pump body is horizontally while the outlet is straight-up.

15. 主泵接于每个蒸汽发生器封头出口的位置也有安全和性能优势，西屋电气称。

The location of the pumps in the channel head of each steam generator also has safety and performance advantages, Westinghouse says.

16. 由于变频器的使用，使泵转速下降，出口压力降低，减少了机械磨损，降低了维修工作量，延长了设备的使用寿命。

Because of the use of frequency converter, so that pump speed decreased, exports to reduce stress, a reduction of mechanical wear, reducing maintenance workload, extended equipment life.

17. 他可以通过泵出口直径90%的颗粒。

They pass solid up to 90% of pump outlet diameter.

18. 结果表明全流道计算可以较好地模拟双流道叶轮的内部流动，尤其是叶轮进出口的流动，并可对泵的外特性做出预估。

The results show that the full passage calculation can simulate the flow in the double channel impeller, especially at the inlet and exit, to assess the pump performance.

19. 泵体和叶轮间形成环形流道，吸入口和排出口均在叶轮的外圆周处。Www.WeNtIYI.cOM

Impeller and the body formed between circular flow, I inhaled and exports in the row outside the circumference of the impeller.

20. 此泵的初次运转时要从吐出口处注油，且到自吸盒完全充满在启动。

For the first operate of pump, the oil should be completely filled in the self suction room.

21. 我们的带有排气消声器和进出口过滤器的正排量泵为您保证顶端缺口的可靠性能。

Our positive displacement pumps with exhaust silencer and inlet and outlet filters assure you top notch reliable performance.

22. 给水泵汽轮机模型采用TUPWR算法，给水泵系统采用SFPUMP算法，最小流量阀采用SOVLV算法，泵出口流量的关系采用压力节点进行计算。

TUPWR algorithm was adopted for the pump turbine model, SFPUMP for feed pump system, SOVLV for minimal flow valve, and pressure node for calculating the discharge rate of the pump.

23. 停止泵压，关闭柱的出口，去除填压用的贮液器。首先从试管架上卸下柱体，然后从槽上拧下贮液器，这样就很容易完成。

Stop the pump, close the column outlet and remove the packing reservoir. This is most easily done by first removing the column from the stand and then unscrewing the reservoir over a sink.

24. 螺杆泵是一种容积式回转泵，当出口端受阻以后，压力会逐渐升高，以至于超过预定的压力值。

Screw pump is a positive displacement rotary pumps, when the export side blocked after, the pressure will gradually increase, so that the pressure exceeds a predetermined value.

25. 泵的吸入口顺着轴线方向，出口与轴线平行。

The inlet is arranged along the axial direction, outlet is parallel with the axis.

26. 液体压强矩阵方程和压电硅片振动有限元方程耦合，得到一个包含微泵进出口扩散管的液-固耦合系统振动方程。

The fluid pressure equation is combined with vibration equation of silicon diaphragm to construct liquid-solid coupling system equations for a micropump.

27. 液体压强矩阵方程和压电硅片振动有限元方程耦合，得到一个包含微泵进出口扩散管的液-固耦合系统振动方程。

The fluid pressure equation is combined with vibration equation of silicon diaphragm to construct liquid-solid coupling system equations for a micropump.