
词语导航
基本信息
词语:焊接缺陷
繁体:焊接缺陷
拼音:hàn jiē quē xiàn
英语翻译
【化】 weld(ing) defect; weld(ing) flaw
分词翻译
焊接的英语翻译:
seal; solder; weld【医】 solder; soldering
缺陷的英语翻译:
blemish; bug; defect; drawback; flaw; limitation; objection; vice【化】 imperfection
【医】 defect; vitium
【经】 defective
翻译例句
1. 在焊接和切割时对人体的危害小,焊接缺陷少。
Reduce health risk during welding and cutting and less weld defects.
2. 弧长太长会产生气孔及焊缝成形差等焊接缺陷。
On the contrary, it will create weld porosity and poor formation.
3. 实现了宏观焊接缺陷和微观焊接缺陷的分类识别。
The classification of macro welded defects and tiny welded defects are carried out.
4. 分析了施焊中常见的焊接缺陷、成因及预防措施。
The welding flaws, cause of formation and preventive measures are analyzed.
5. 进行弯曲试验确定韧性和是否存在某些焊接缺陷。
Bend tests are performed to determine ductility and to determine the presence or absence of certain defects.
6. 在现代焊接生产中,焊接缺陷的出现都是不可避免的。
Welding defects is inevitable in modem welding manufacture especially in manual welding condition.
7. 浮顶罐蒸汽除蜡装置失效的原因是施工焊接缺陷和热应力破坏。
The weld defects and thermal stress result in failure of vapour wax-removal loop-pipe used in floating roof tank.
8. 研究现状表明快速冷却有助于减少焊接缺陷,提高焊点可靠性。
It should be payed much attention to fast cooling because it can decrease the defects of PCB assemblies and promote the reliability of solder joint.
9. 该工艺操作简便,减少了焊接缺陷,提高了焊接速度和焊接质量。
The operation of this technics is easy, welding defects are reduced, the welding rate and quantity are raised.
10. 断口扫描电镜观察显示断口有一定的塑性,未发现气孔和焊接缺陷。
SEM showed no pores and other defects and some ductility at laser welding area.
11. 分析了铝热焊焊接过程中出现的各种焊接缺陷,并提出了预防措施。
This paper analyzes various welding defects appearing in the process of thermit welding, and advances some control measures.
12. 分析了彩色玻壳屏模具焊接缺陷原因,并介绍了相应的问题解决对策。
The defects reasons for color glass shell screen die welding are analyzed, and related solutions are introduced.
13. 本文是结合课题“焊接缺陷X射线实时成像检测系统的研究”来进行的。
This thesis is based on "the Research on X-ray Real-time Radiography Inspection System for Welding quality".
14. 本文介绍了作者自行设计的铝合金焊接缺陷及工艺问题分析诊断专家系统。
The paper introduces an expert system for diagnosing weld defects and analyzing welding process problems.
15. 焊接裂纹是常见的焊接缺陷之一,焊接裂纹的存在常常导致严重的航运事故。
Welding crack is one of the important welding defects, which often leads to serious shipping accidents.
16. 提出了根据模糊综合评判、定义结构参数用以表示焊接缺陷损伤程度的方法。
A fuzzy multicriteria modelling method of defining a structural parameter for representing the grade of welding defect damage is presented.
17. 桥连现象是波峰焊接过程中最常见的一种焊接缺陷,其影响因素是多方面的。
Bridge phenomenon is a frequent defect in wave soldering, which have many affected factors.
18. 大庆至铁岭输油管道由于焊接缺陷,导致管道发生破裂,严重影响了输油生产。
Pipeline rupture resulted from welding defects in Daqing-Tieling oil transport Pipeline greatly affected oil transport production.
19. 结果表明:焊接工艺参数合理,在焊接接头未发现任何焊接缺陷,焊缝质量良好;
The results show that the welding parameters were reasonable, and any welding flaws were not found, and the quality of welded joints were good.
20. 该研究对提高LED封装的可靠性和提出检测LED焊接缺陷的方法具有重要意义。
The research is important for improving the reliability of LED packaging and proposing the method of detecting welding faults during LED packaging.
21. 在井架的制造过程中,焊接缺陷、焊接变形和焊接冷裂纹是影响井架质量的关键因素。
During the manufacture of oil derrick, such factors as welding defects, deforming and cold crack have key effect on the oil derrick quality.
22. 高频焊接制管是最快和最有效的制管方法,但高频焊接制管会产生各种各样的焊接缺陷。
The high frequency welded pipe production is the fastest and the most efficiency way to produce pipe, but it also produces varies kinds of weld defects.
23. 由于RTS 曲线的升温斜率可以很好的控制,这样可以减少组件的焊接缺陷和热冲击。
This also will promote better wetting , and thus the RTS should be used on difficult-to-wet alloys and parts.
24. 应用高效的气体保护熔化极电弧焊焊接铝合金薄板时,容易出现熔池下塌、烧穿等焊接缺陷。
Welding defects such as collapse of molten pool, burning through, would like to happen in the high efficient gas shielded metal arc welding.
25. 结果表明,该轴断裂是由于轴表面存在焊接缺陷,在旋转弯曲应力作用下产生低应力疲劳开裂。
The results showed that the weld detects on the surface of the axle was the reason to cause low stress fatigue under rotation bending stress which finally lead to the fatigue cracks on the axle.
26. 横向焊接时由于熔化金属重力的作用,会引起熔池金属下淌,从而产生咬边以及焊瘤等焊接缺陷。
In horizontal position welding, the gravity makes molten metal flow downward and sometimes causes weld defects such as undercut and overlap.
27. 利用X射线底片扫描成像法得到铝合金焊缝图像,再通过图像处理方法即可得到焊接缺陷二值图象。
Processing the aluminum weld image from the scanning of the X ray negative can derive the binary image of the weld defects.
28. 本文阐述一般球罐焊接缺陷的有关断裂力学计算,介绍了由于角变形和错边量引起的附加弯曲应力。www.WEnTiyI.coM
This paper deals with the general calculation of fracture mechanics on the weld defects of a spherical tank. The additional bending stresses caused by both the angular distortion and the stagger toe.
29. 本文阐述一般球罐焊接缺陷的有关断裂力学计算,介绍了由于角变形和错边量引起的附加弯曲应力。
This paper deals with the general calculation of fracture mechanics on the weld defects of a spherical tank. The additional bending stresses caused by both the angular distortion and the stagger toe.
版权声明:问题易所有作品(图文、音视频)均来源网络,版权归原创作者所有,与本站立场无关,如不慎侵犯了你的权益,请联系我们告知,我们将做删除处理!
