
词语导航
基本信息
词语:锁紧
繁体:鎖緊
拼音:suǒ jǐn
英语翻译
【计】 lock stock and barrel
分词翻译
锁的英语翻译:
lock; lock up【计】 lock stock and barrel
【医】 lock
紧的英语翻译:
close; tighten; pressing; short of money; strict; urgent翻译例句
1. 他全神贯注地锁紧眉头。
He wrinkled his brow in concentration.
2. 将你锁紧进心底,将记忆彻底记忆。
Will lock into the bottom of my heart, you will complete memory.
3. 他们不能指示锁紧力究竟是多少?
They can not tell how much the mould clamping force is on earth?
4. 建筑材料;锁紧装置;锁;试验。
Building materials; Locking devices; Locks; Testing.
5. 即唐氏螺纹紧固及硬锁紧螺母紧固。
Tang thread fastening and forced lock nut fastening.
6. 针对锁紧弧面的磨损提出了改善措施。
The measures for improving wear of camber for lockup were proposed.
7. 压低手柄,然后锁紧螺丝。
Lower handle and tighten screw.
8. 警卫退出了牢房区,锁紧了牢房区出入的门。wWW.wEntiYi.cOm
The guards back out of the cell block and lock the gate behind them.
9. 调整后,拧紧锁紧螺母。
After the adjustment, screws tight the stopping nut.
10. 他的手背在身后,手腕被一根连锁紧紧绑着。
The man"s hands were behind his back, the wrists bound with a cord.
11. 通过各种测试,强力锁紧螺母已被证明是有效的。
Hard Lock Nuts have been proven effective in a variety of tests.
12. 滑动并敲击贮油槽扣件夹,直至凸耳锁紧外壳。
Slide and tap in reservoir retainer clips until TAB locks to housing.
13. 逆时针方向旋转锁紧螺母5,使其退到适当位置。
Revolving the lock nut 5 anti-clockwise to the suitable position.
14. 为单个导体消除电缆应力。不再需要电缆锁紧头。
Cable strain relief for single conductors. No need for cable glands.
15. 当你到达流线、锁紧用手鼓励的身体来做这个工作。
When you get to streamline, locking tightly with the hands encourages the body to do the work.
16. 对轴承密封,牙轮锁紧,喷嘴安装等也有新的意向。
There is also a new Intention on bearing"s seal, roller"s locking and nozzle"s mounting.
17. 双件套强力锁紧螺母安装简便,只需要一个扳手就行。
The two-piece Hard Lock Nut is easy to install, requiring only the use of a wrench.
18. 测试程序:扭转插头后机械锁紧装置处在工作状态。
Test procedure By twisting the connectors test that the locking mechanism is engaged.
19. 强力锁紧螺母非常适合在飞机,汽车和建筑的应用当中。
Hard Lock Nuts are ideal for use in aircraft, automotive and construction applications.
20. 如果您想调节它的位置,需要订购另外一个锁紧螺母。
You"ll need to order an extra jam nut if you want position-adjustability.
21. 在调节完成后,紧固锁紧螺母,重新安装快速进水手柄帽。
After completing adjustments, tighten the lock nut and replace the fast fill lever cap.
22. 由于它独特的圆锥面接触锁紧使其达到安装固定的最佳状态。
Because of its unique locking taper contact, it is able to reach the best status fixed.
23. 甚至在螺母松脱45度的情况下,其一半以上的锁紧扭矩仍然不变。
Even when loosened by 45 degrees, more than half of the tightening torque remained.
24. 拆卸探头时,先将探头锁紧开关打到开的状态,水平拔出探头即可。
When the probe is taken down, turn the lock switch of probe to OPEN, pull out the probe on the level state.
25. 松开和拆卸隔膜锁紧螺母和锁紧垫圈,从阀杆上往下压阀盘和隔膜。
Loosen and remove the diaphragm lock nut and lock washer, pressure plate and diaphragm from the valve stem.
26. 同样可以尝试不同的绑鞋带方式来增加鞋子上部的包裹性,并锁紧鞋跟。
Also experiment with different lacing patterns to more securely wrap the top of the shoe and lock in the heel.
27. 锁紧螺钉必须涂上足够的油脂,注意所有油脂不得含有二硫化钼添加剂。
Locling the screw must spread enough oil, please notice all oil should not contain molybdenum bisulfide additive.
28. 如果要清洗或更换部件,关闭供应管道,松开锁紧螺母,退出调节螺丝。
To clean or replace parts; shut off supply, loosen lock-nut and back off adjusting screw.
29. 如果要清洗或更换部件,关闭供应管道,松开锁紧螺母,退出调节螺丝。
To clean or replace parts; shut off supply, loosen lock-nut and back off adjusting screw.
版权声明:问题易所有作品(图文、音视频)均来源网络,版权归原创作者所有,与本站立场无关,如不慎侵犯了你的权益,请联系我们告知,我们将做删除处理!
